I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
hi,
We are working on nRF9160 DK board.
One of the issues is how to save secure data (e.g, data key) into flash. Is there any examples or document on data storage APIs...
Hello,
i am developing on nRF52840 using SDK 15.2.0 and Softdevice 6.1.1.
I recently noticed, that when i first bond with the nRF52840, then disconnect and delete the...
Hello,
I am using nRF52840 development kit and I wanted to know with use of the source code of nRF blinky application can i modify as per my project requirement and make...
I am connecting debug out on the NRF52 DK to a production board for programming. I am using Tag Connect connection and need to make sure I route pins properly. I cannot find...
Good morning,
I'm developing a new product based on nRF52840 and S140 (v6.1.0). I'm able to connect using my smartphone using the following data:
sec_param.bond = SEC_PARAM_BOND;...
Hi, sorry for if this has been answered elsewhere.
I am currently designing the production setup for a product using the nrf52840 as a BLE radio.
I can't find how the...
Following this tutorial: www.novelbits.io/.../ some doubts arose in my head.
My doubts concern Android app witch name is: nRF Mesh. This application is used only for Provisioning...
Our BLE DFU has stopped working in SDK 3 so I have tried to simplify it by going back to SDKs.
If I compile D:\NordicSemi\nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\Examples...
Hi, I have a question about Bluetooth mesh secure provisioning, as it is described in the spec section 5.4.3.
The spec states that either
1) both OOB public key exchange...
We are looking to implement "dynamic" BLE services that can be configured (i.e. enabled/disabled) externally, however from the examples there appears to be no way of de-initialising...
Hi,
I have nRF9160 DK. I want to update firmware to (From Your WebSite: Link Pasted)
nRF9160 LTE-M/NB-IoT/GPS Modem firmware
https://www.nordicsemi.com/Products/Low...
Since nrfConnect Programmer, ninja flash/west flash ALL use nrfjprog behind the scenes, I wish I could find out _exactly_ which nrfjprog commands the nrfConnect Programmer...
Hi,
I'm trying to reduce the current consumption. I can't use sd_power_system_off because I don't want my device to rest when it wakes up. So the other way to do this is...
