I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I was wondering if it is possible to change some of the BLE Stack Configurations based on the number of devices connected...
e.g. Changing Connection Interval and...
Hi,
I am evaluating the Firmware on this github repo and my nrf52832.
At the moment I am compiling it using my makefile, however I would like to import this project...
Hi All.
We have flashed the hex-file of ble_app_blinky for pca10040 on the debugger, and things work fine.
We are using sdk-15.2 with softdevice-6.1.1
So, a question...
Hi there, I am having issues knowing how to get access to data coming through a VisualGDB embedded (C) project using the pc-ble-driver. I have my project working fine and...
Hi ,
Nrf52840.SDK15.2,Windows,Ses
Compile "secure_bootloader_usb_mbr_pca10056_debug " project, An error occurred. As follow：
Cannot open file: E:/new/project/wireless...
I have used the UART example up and got it working. So i can send and receive data using it.
However i wanted to modify it so as to run with the current RTOS environment...
Hello
According to BLE Specifications we should be able to get 125kbits/s over the air transmission i cannot seem to get anything remotely close to this.
Is there something...
I use Multilink and Blinky Demo with PCA10056 and PCA 10040 Board,when the two board close to each other there is no packet loss,but when i dispath each other with 50cm,there...
Hi,
I am currently using two different programmers(nrf51DK, Segger flasher portable plus), programming software's ( NRFgo Studio, Jflash). Here are my issues:
When I...
Got this error while trying to perform a DFU over BLE (noble) on a raspberry pi 3. The peripheral should be running v15.
Here is the partial log just before the error...
Hi,
on nrf51 chip we had a reset issue during ESD testing. One of the SWD lines was susceptible to this and caused nrf51 to reset. We had to ground this line after programming...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask if I use pm_peers_delete() to delete a bonding data, Is the data completely erased...
Dear sir.
I have a question about the nRF2460.
As far as I know nRF2460 chip already discontinued right?
The future NORDIC company will not make new wireless audio...
Hi support,
We design a standalone sensor module with nRF52832. We would like to use CR2450 coin battery for power supply. Can CR2450 coin battery be used to supply nRF52832...
