I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello there,
I am working in my master degree project with nordic NRF51822 microcontroller, but I faced two problems. I don't know if is a SD problem or hardware problem...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LE_TEST_END in DTM.
I tested with nRF52832...
Hi!
I have old code written in nRF51 enviorment with SDK nRF5_SDK_12.0.0.
I've successfully flashed the softDevice (s130_nrf51_2.0.1_softdevice.hex).
No error occurs...
hi, I am fresher starting my carrier in ASIC i am learning about UART where i come across with the word "DEADBEEF" in the coding please help me with where it is used and how...
Hi We've been using SDK12.1 with softdevice 3.1.0 on a NRF52832 for some time now. Now we want to upgrade our SDK to 15.2 with softdevice 6.1.0. We've converted the application...
Hi all,
I am working on nRF52840, nRF5_SDK_15.2.0, pca10056,usbd_cdc_acm
I can now communicate nrf52840 with PC,However, I failed to connect nrf52840 to android, Android...
Dear Team,
Greetings !!!
Device - nRF52832 Softdevice - s132_nrf52_6.0.0 IDE - segger embedded studio Bootloader - secure bootloader
In our current application, We are...
Hi,
We have build complex application based on Nordic SDK. Right now we are thinking about moving to Zephyr OS. I was wondering if there is any tutorial/tips I can find...
Hi, I'm using nrf52832 development board. In which i have flashed hci_uart example code of zephyr (latest code taken from https://github.com/zephyrproject-rtos/zephyr ) which...
Hello,
Our product is configured to use 3 total GPIOTE channels –– 2 sensors configured for "high accuracy" GPIOTE events, each around 10Hz refresh rate, and 1 using "low...
Current consumption during k_cpu_idle() after GPIO interrupt does not take the same value. Why does this happen? Any idea? Thank you for reading this post in advance.
<Environment...
hi all, i'm using uart with easyDMA, and i'm disabling and enabling it back on my code. before disabling the uart TX and RX works fine. after disable&enable i get wrong data...
Hello,
as part of the development that will soon be in production, I would need to be able to authorize or not the pairing according to an internal state of my device. ...
The memory returned by the pointer returned from cJSON_PrintUnformatted() in below file must be freed.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master...
I m analysing application source code searching for implementation of INDENTIFY.
The problem is that application has hundrets of classes and it is very complex so it is...
