Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
I would like to modify the current default SRAM partition from 64k (secure), 64k (bsd), 128k (non-secure). I would like to change it as follows; 8 k (secure), 8k...
See: https://devzone.nordicsemi.com/f/nordic-q-a/46833/nrf-connect-can-t-see-nrf52-dk/185284#185284
I have been developing a peripheral with nRF52832 and SDK 15.3.0.
I...
I'm stuck over fds_init() which hangs on mbed-os using SDK 14.2
I am calling fds_init within bleInitComplete callback as follows:
BLE & ble = BLE::Instance ();
ble...
Hello,
The pwm example shows changing the duty cycle inside the main while loop with delay wait.
I would like to get rid of this delay wait by putting the app_pwm_channel_duty_set...
Hi, may I know whether there is a way for nRF52832 chip to directly have access to the variable gain amplifier (VGA) inside the chip? Namely, our input signals goes directly...
Hi,
I am using the sdk 14, S132, ble_app_uart example.
My nordic chip receives data from the MCU over UART and passes out to mobile application over BLE.
using the nrf...
hi i am trying to integrate nrf_butoonless_dfu service in ble_app_uart code in nRF sdk 15.3.0,
i have added the all the required source files and include files and macro...
I am attempting to implement an application using the s140 6.1.0 softdevice on an nRF52840 which "concurrently" advertises as a connectable device while at the same time transmits...
I try to solder a EBYTE NRF52840 module by my PCB and connect with SEGGER programmer. I try to connect to 4 wire VDD, GND, SWDIO, SWCLK, like the one that I have with NRF52832...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0. I use gcc. I just got it to link and flash and I'm seeing RTT logging OK, to a point. I also have the flashlog in use...
in my application use nrf52 connect with max6675 thermo couple for read temperature
max6675 is configurable in spi mode.
in main.c
in 'nrf_drv_spi_init' not...
Hello,
I use the LAIRD module BL652 with an nRF52832.
My project used the RTC as date/hour counter. I used this RTC to increment a counter each 125 ms of RTC interrupt...
Hi,
I am using s132 6.1.1 with SDK 15.2, developing with keil , my code works completely fine on Development Kit but it doesn't boot up on our custom board which doesn't...
Hello all,
I updated modem firmware mfw_nrf9160_0.7.0-15.alpha.zip. I have iBASIS SIM card in modem and started with at_client example and country also has nb-iot support...
