Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I am working on implementing concurrent BLE UART central and peripheral service. I am doing this by taking "ble_app_hrs_rscs_relay" default example as a reference. ...
Hi, how i can mark internal flash memory nordic for user data and logs, and protect them from being overwritten when updating firmware over the DFU?
Thanks!
hey nordic,
it has been 10 days since there is no reply.
please any nordic engineer reply in this thread
https://devzone.nordicsemi.com/f/nordic-q-a/45470/encryption...
Hi,
We are developing a new internal engineering tool that mostly does passive scanning on the NRF52840 dongle connected over USB but I'd like to be able to switch to...
The relay successful rate of my Mesh setup is not 100%. I think light server miss packet from light client. I have tried to change configuration following:
1 #define BEARER_SCAN_INT_DEFAULT_MS...
HI,
We are currently using System ON mode with RTC is running, and we are not facing any problem. But our concern is power consumption
We are using below peripherals with...
Hi,
I am try to send many data via ble_nus_data_send() function, but I found "Host can not receive any data if ble_nus_data_send() is execute busy".
So, I have two questions...
Hi to all,
I am developing an app based on nordic NRF52840 soc and i want to implement a peripheral device that can connect to multiple central devices in same time and...
Hi,
I'm using nRF52840 and I have some issues with direct advertising.
When I'm using fast mode advertising everything is OK. While using direct mode, I do everything...
Using SD 6.2 and sDK 15 I need to write to the UICR_Customer space while the BLE system is operating.
I tried pulling example code from https://devzone.nordicsemi.com...
Hi,
I want to program my nrf52 DK through OTA programming. In my project I don't use Bluetooth.
Is it possible to program the board using the Radio without a Bluetooth...
Does anyone here can share the source code for a small program written in C or C++, which can be compiled on a Windows machine, and can receive the orientation data from a...
Hi. I have just installed the new windows nRF connect 2.6.2.
How do you do secure DFU? There are no apps in the list to do that. On your website it says it supports DFU...
In my attempt of learning the nRF52 "eco system" (nRF52 DK, nRF15.3 SDK, SES and pca10040e project for nRF52810), I have combined the GATT_C, GPIO and SPI examples to make...
Device/SW Info:
Ubuntu 18.1 SDK : 15.0 SD 132 v 6.0
NRF52832 QFAAE1
The device once connected to the device is immediately dropping the connection upon going into...
