I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
I noticed S110 is not listed as supported by nRF5 SDK11. However, no supported SoftDevice seems to offer the same functionality as the S110 (Peripheral only protocol stack...
Hi,
in SDK v9, i tried to compile the bootloader example, but:
/usr/lib/gcc/arm-none-eabi/5.3.0/../../../../arm-none-eabi/bin/ld: region `FLASH' overflowed by 6944 bytes...
Did anybody know how I could determine the connection interval for a established ble connection between an android (4.4) central and a (e.g. nRF51822) peripheral?
I've been having a little bit of an issue trying to parse UART data that I am receiving from an external device.
Where I'm having issues right now is comparing an incoming...
Every 10 packets send; it will have at least 1 packet with 1-2 bytes corrupted data.
The configuration as below:
data rate: 2Mbps
channel: 7
Prefix0: 0xE2
BASE0...
Hi,
We have an application that can run in two modes. The mode is selected by setting the GPREGRET to 1 or 0 and restarting.
Currently we are running this procedure directly...
Hi,
We are developing a product using the nrf 51422 where the power source is a 3 phase generator.
We rectify and charge on a supercap where the uProc is being supplied...
Please correct me if I'm wrong but my understanding is that unused RAM banks can be disabled to reduce quiescent current.
My first question is what is the current consumption...
Hi,
I'm using RTT debugging with soft-device " https://devzone.nordicsemi.com/tutorials/6/debugging-with-real-time-terminal/ " , I'm able to print few messages, after which...
Hi~ I'm sorry because it usually does not use English writing in English, So there may be errors in English please forgive me.
Last year, I bought some nRF51 Development...
Short: Working Timer. Working SPI. SPI does not work when triggered by timer_handler.
Hello,
I am currently trying to replace delays with timer in my code...
I set...
Hi.
I'm using PCA10028, SDK10.0.0 S130.
I want to make nRF51 goes sleep mode.
So I tested linked source code as below.
github.com/.../main.c
It works well.
But...
Hello, Nordic Stuff.
I've been working at ble peripheral devices using S110.
I am just wondering why the sd_ble_gap_disconnect function accepts only the reason code...
