Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hey all,
I'm trying to install the nRF Asset tracker. I'm stuck at a step called Building the project using GitHub. I just need to know how to build the project using...
Hi,
I was trying to retrieve the log information from the Nordic to the AWS server. I can see all the log info with the Status as Error. I'm retrieving the logs from...
Dongle cannot enter reset mode, and led is not pulsing(no shine ) when I connect to PC, the device cannot detect it,too. Is their any problem on the firmware, the device cannot...
Hello there,
I am trying to find the datasheet from the device NRF31502 F but I am having some trouble!
Can someone help me or point me where I can get it?
Thanks
Dear all. Now I am working on multi-peripherals to one central NUS communication project. The peripheral boards are based on nRF52840 and the central board is nRF52832 DK...
Hi Team,
We want to write our own MAC address on nRF52840 module. It's a production level MAC address i.e. it is fixed MAC address cannot be overwritten. What is the procedure...
Hello,
I am using SDK 14 & nRF52832 & peripheral role; I have setup a timeout in the order of several seconds, and during this time my device shall advertise but reject...
Hi,
I'm using nrf52840 and trying to define the pin mappings for my custom board. In order to do this I'm studying the board definition of pca10056 (pca10056.h).
In...
Hey all, I'm trying to run the node cli flash "imei" -f /path/to/firmware.hex command on the terminal. It prompts as ERROR flash <deviceId> failed!,
ERROR Error: No such...
Hi
I'm working with version v8.6.90 since the master version at this date have an Auth amplify issue.
The Fetch function on the map is buggy :
Here is the Chrome dev...
We are using nRF52 SDK 17.0.2 s132_nrf52_7.2.0_softdevice.hex in our application. When entering in DFU mode from application, we perform nrf_power_gpregret_set(BOOTLOADER_DFU_START...
I am willing to use nRF52832 chip in one of my project. But all the breakouts dont fit the size and I want to design my own PCB with i2C accelerometer. I only want to transmit...
Hi,
Corect me if I'm wrong, but the initiation of ble_gap_addr_t.addr_type in main.c in the HRS_C demo is not necessary, as the addr_type is calculated based on the address...
Hello Folks,
I am following below steps to add Zigbee FOTA to Zigbee: Light switch example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_zigbee_configuring_libraries...
Another problem is that when I turn on I2S to read data, the while loop does nothing, and the broadcast can't be transmitted, just like I2S has occupied all the CPU, and other...
