Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Arm Gcc (using Eclipse Neon) |
SDK 13.0 |
nrf52 DK (PCA10040) |
tried soft device 4.0.2 and 4.0.4
I can successfully compile and run the example -ble peripheral- ble_app_hrs...
Are there any particular practices or instructions should i follow if I want to write a custom library
We are trying to write a library for LEACH protocol and it is a network...
I spoke with someone at Nordic who seemed to imply that utilizing the radio does not necessarily tie up the Cortex processor on nRF5X devices. Is this true? It seemed to me...
I am trying everything.
In sdk_config: #define UART_DEFAULT_CONFIG_HWFC 0
In the nrf_cli_uart.c I changed it to APP_UART_FLOW_CONTROL_DISABLED,
in the pca10040.h I...
Hi , I have 2 nrf51822 borads. One is with nRF5_SDK_12.3.0_d7731ad\examples\ble_central\ble_app_hrs_c and the other is with nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral...
I would like to use the ble_app_uart_c example, found here , to connect to a custom peripheral. What values should I change in the central device code in order to connect...
I know that BLE is not suitable for high-volume streaming.
So how do BLE earphones stream audio?
Does it use with bluetooth classic protocol?
And I coundn't monitor...
Hi,
I've one central and one peripheral devices. I'm trying to make a connection between them, perform a bonding process and finally add the peripheral id in the whitelist...
Hello All
I am developing BLE based home automation system using nRF51422 DK for my research activities. now i am planing to make separate PCB nRF51422 device alone. i...
Hi,
I'm trying to get the RSSI of incoming 802.15.4 packets using otLinkRawGetRssi() , but I need only RSSI from one specific device. I tried to use whitelist ( otLinkSetWhitelistEnabled...
Hi, I ran the example code ble_hrs_c in nrf51822 16KB RAM version and 32KB RAM version. The 16KB RAM version works fine. But in the 32 KB RAM version, peer_manager_init(true...
I modified the HTS app in the nRF toolbox to test adding other services like below.
In detail, I added mDICharacteristic field to save the information of System ID...
Hello,
I developed a Nordic board with 2450AT18B100 chipset antenna. I follow the design of Solar Powered Sensor Beacon.
infocenter.nordicsemi.com/index.jsp
I test...
Hi, I'm building a product with use this kit www.nordicsemi.com/.../nRF52-DK and I would like of know how write the firmware in others CIs to can use in my circuit board....
Hello,
I am currently working on project that uses BLE peripheral and BLE central for automatic sensor calibration on custom board. There is an initial connection where...
