I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear Nordic devzone community,
I have designed a custom board using nRF9160 and I am able to send and read out certain AT commands which confirms to me that most of the...
I'm transitioning from SES to Visual Studio Code.
In SES, I can define multiple builds and then define preprocessor options (eg. -DOPTION1) for each build definition
I...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
Hi,
I'm trying to setup my NFR52840 DK to act as a NFC tag so that I can read some simple data on my phone via NFC transfer.
I have tried a few NFC sample applications...
Hi,
I am using a modified HTTPS Client demo code [Let's say Version A] and sometimes when trying to debug with Segger Embedded Studio for ARM (Nordic Edition v 5.34a/Jlink...
Hello,
From time to time I am getting the error " Unable to find bootable image" when I start a debug session in SES-NE v5.60.
FIH_CALL(boot_go, fih_rc, &rsp); if (fih_not_eq...
I am trying to read the GPIO state on an nRF52840 right after it wakes up from deep sleep (System OFF mode). I have configured 4 pins as wake-up sources from deep sleep System...
I have been working on finding the cause to an unexpectedly high power power consumption in several newly produced units of our product based on nRF5340. I believe I have...
I'm trying to build a custom secure partition, but get the following error when building:
However when navigating in files to the directory the file "tfm_custompartitiontest...
Hi All,
My team recently reserved a custom service UUID with the Bluetooth SIG, and we'd like to replace the custom 128-bit UUID we had been using in our products. Can I...
HI
We are mass producing NUS-based products.
During mass production testing, pairing is performed and functionality is tested by pressing buttons, etc.
However, pairing...
I'm using
AT_MONITOR ( catch_all , ANY , on_modem_at_notification );
and I'm just printing the notification on reception:
static void on_modem_at_notification...
Hello,
I would like to add to my project new i2c slave (for example - dac5571 from TI). In the DTS overlay - under the i2c0 node I need to specify compatible , and I don...
I have configured the nrf52840 DK one board as Peripheral and other as central.
Added multiple services and characteristics. I am sending some data at every 20ms using notify...
