Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
We have some custom hardware that utilises an NRF52832. Up until recently, all our firmware was built on NCS V2.2.0, which I believe used Zephyr V3.2.99. We have implemented...
Hi,
I am moving to version 2.6.0 of the SDK and toolchain. I am developing on windows 11 pro. Our cMakeLists.txt file creates a version file in our conf directory version...
Hello,
We have a custom board using a nRF5340.
We followed this course implementation for simple serial recovery over UART (and also tried CDC ACM) but as soon as activate...
Hi, I am trying to download all software necessary to program nRF chips. I am following this academic course Lesson1 When i try to install nRF connect SDK after toolchain...
We would like to develop for the waveshare 1.02 e-paper display. We have limited experience with SPI on Zephyr and are looking for the easiest way to get a "hello world" result...
Hi everyone!!
Im very new to this firmware space and would love some help.
Currently I have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
Hi everyone,
I have a fairly mature project that I am now required to add MCUboot to so that remote firmware updates can be possible. I am building for a custom board based...
Hello,
I use a RF52-DK board for flashing/debug Nordic microcontroller. When I connect the board on my mac, the "JLINK" volume is mounted/ unmounted every 2 seconds and...
Hi,
I tried the radio_test sample with the sdk 2.3.0 on a custom board. I added this to the prj.conf
And this to the app.overlay
With this I had a ttyACM0 and...
I have used ncs-example application workspace to develop our project. In that we were trying to include WIFI, so we include all (sample/wifi/sta) content to my project. but...
Hello,
I recently upgraded the MDK from an "inherited" much older version in my project to MDK version 8.63.1 for GCC. There is now a file called startup_nrf_common.c that...
I used a script to write the Gateway and Headset to the nRF5340 Audio DK board.
I used VSCODE to write the Gateway source and Headset source to the RAYTAC board.
I tried...
We have a problem where a display running on 5V with an UART on 3.3V will self-bias through the UART TX pin when the 5V supply is switched on.
How do you make zephyr not...
