Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
hello Nordic
i work with ncs 1.7.1, with nrf52832 soc
i tried to add a driver and for some reason i fail and i can not understand why
this is my dts
this is...
Hi,
we use the NRF52840 as a connectivity chip in a serialized application (based on nRF5-SDK v17.1.0 and SoftDevice S140).
When our main app starts, we would like to...
Hello,
While using the at_client sample, when the SMS is received, the following notification is seen
How can I have the access to these notification in other application...
Hi all,
I was recently asked about using L2CAP Connection-Oriented Channel (CoC) to increase thru-put of a project. This must be a gap in my knowledge as L2CAP was always...
Hello,
I've a query.
I am trying to build and see output of " Power Management Example".
C:\nrf_sdk52\DeviceDownload\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560...
Hi! We are trying to send an HTTP request to our AWS Web Server. The problem that we are figuring out now is that we don't know the way to add a body to our request. We based...
Hello, I am trying to set up my Thingy91. I am using the latest modem firmware mfw_nrf9160_1.3.2 and have also successfully updated it with the J-Link EDU Mini as described...
To the kind attention of Nordic support team,
I have a project that is exploiting either gzll or BLE protocol. I'm using gzll_nrf52840_sd_resources_gcc.a libraries, that...
Hi, Following my previous ticket on the matter, , I have attempted to DFU an MITM bonded device to LESC code, such that the peripheral device will disconnect connections that...
I used the nrf edge impulse app and a nrf53 to collect and build a first model to detect a state of a dishwasher. After deploying it and seeing the interference method, i...
The are some examples that explain how to use the driver ieee80215_dw1000?
There are is a ble profile that can be used for the managment of the UWB devices?
Best Regards...
Hi,
I have an error with the new SDK Version 2.1
This concerns the implementation of the LTE configuration:
My prj.conf:
# LTE-M (LTE-CatM1)
CONFIG_LTE_LINK_CONTROL...
In ESB, what is the function of esb_config. selective_auto_ack? What is the relationship between esb_config. selective_auto_ack and esb_payload.noack ?
Hello,
I'm using the Fanstel BC832 module which contains Nordic's nRF52832 BLE chip on a custom PCB board. When trying to run the Blinky example on PlatformIO, it works...
Hello,
we are debugging the asset_tracker_v2 on nRF9160 DK in VS Code with the nRF Debug backend, but unfortunately the global and static variables are not shown in the...
