I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I’m working on the T5838 Invensense PDM driver for the nRF54L15 .
I’m referencing this driver: IRNAS T5838 Driver , and have updated it to work for SDK 3.0.2 (including...
Hi Nordic teams,
I am working on integrating single-slot DFU for the nRF54H20 based on the throughput example. However, I noticed a difference in how the Bluetooth controller...
Hello,
We developped a new rf board with 54l15 µc.
We discovered our UART communication have some errors with -16 °. At -20 ° the device doesn't respond.
I changed...
Hi，
Hello, I frequently need to perform BLE DTM testing, but there is only one CWM500 instrument available, and I have to queue up and wait for it every time I run tests...
hello Nordic
we are working with nrf52840/nrf52832 with ncs (currently on v3.0.2)
i have noticed that when i try to dfu a merged artifact of my version with the new mcuboot...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
Hi, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK : nRF...
Hello,
I am working with the nRF9151 and would like to request the most complete available documentation describing all GPIO pins (P0.0, P0.1, ... - P0.31) and their functions...
I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
Hello, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK...
Hello,
After working with the path loss monitoring sample in NCS, I was wondering if there is a sample that accomplishes something similar to the following:
Central...
I'm programming a batch of 100 NRF52840 devices (new ISP1807-LR modules), and I'm unable to recover or program several of them. Most work fine, and I've never seen this issue...
I want to enable in nrf Connect SDK for nrf54L MCU FW image encryption for upgrade. In the project we use NSIB B0 bootloader plus MCUBoot with ability to upgrade MCUBoot and...
Hi,
I have a project requirement to interface with HART, which is a protocol that specifies odd parity for UART. I recently found out UART odd parity isn't supported on...
