Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello all,
I`m trying to use k_poll, it`s working okay, I just have an hard fauld error that drives me crazy, I have in main an loop which listen to k_pool_signals, the...
Hi,
Why I use the function m_device_state_set(cons, PM_DEVICE_STATE_SUSPENDED); to close the serial port is still a large current:38.80uA?
The verification method is as...
Hi there
I wrote SDK 17.2 ble_app_hrs to the module.
When connecting to an Android device, Empty PDUs will no longer be sent. I checked the RTC COUNTER, but it is incremented...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
We are in the process of adding FOTA to our custom project and...
We are using nRF52833 with DFU secure bootloader and implemented DFU master/host on ESP32 BLE. We observe that DFU bootloader get stuck in above locations in softdevice more...
Hi Nordic
I have been using your example on USB MST to embed it into my application
Everything works ok, but in the main loop im constantly polling for USB power event...
I'm looking at the nRF Connect SDK Matter documentation, and the intro page states :
"If you are new to Matter, check also the tutorials on DevZone ."
The link in...
I am using nRF5340DK and would like to send and receive data to computer via UART1 and pins "TX", "RX", "CTS" and "RTS" using USB TO RS232 SERIAL CONVERTER.
This way I...
Hello Nordic, I have a problem. I'm running the nRF9160DK with three sensors and an sd card reader. The three sensors and the sd-card reader are connected via SPI. Due to...
Hi,
I would like to generate interrupts triggered by an input clock pin at 2 MHz to sample an 8-bit digital signal. I am trying this with an nRF5340. Up to this point...
Hello,
I am working with a nRF52833 and I am no longer able to use my JLink Base to flash it. I was previously able to flash it and there was no hardware change at all and...
Hello,
I am writing code in zephyr on nRF52840. I am advertising my BLE. and we have a stable android app (built-in a flutter). My problem is when I am trying to write an...
Hi teams,
Recently, during my test with some Arduino-Shield compatible daughter board with nRF52833DK, I found some pin mapping is incorrectly defined in nRF5 SDK.
The...
