Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hey all,
I'm trying to install the nRF Asset tracker. I'm stuck at a step called Building the project using GitHub. I just need to know how to build the project using...
Hi,
I was trying to retrieve the log information from the Nordic to the AWS server. I can see all the log info with the Status as Error. I'm retrieving the logs from...
Dongle cannot enter reset mode, and led is not pulsing(no shine ) when I connect to PC, the device cannot detect it,too. Is their any problem on the firmware, the device cannot...
Hello there,
I am trying to find the datasheet from the device NRF31502 F but I am having some trouble!
Can someone help me or point me where I can get it?
Thanks
Dear all. Now I am working on multi-peripherals to one central NUS communication project. The peripheral boards are based on nRF52840 and the central board is nRF52832 DK...
Hi Team,
We want to write our own MAC address on nRF52840 module. It's a production level MAC address i.e. it is fixed MAC address cannot be overwritten. What is the procedure...
Hello,
I am using SDK 14 & nRF52832 & peripheral role; I have setup a timeout in the order of several seconds, and during this time my device shall advertise but reject...
Hi,
I'm using nrf52840 and trying to define the pin mappings for my custom board. In order to do this I'm studying the board definition of pca10056 (pca10056.h).
In...
Hey all, I'm trying to run the node cli flash "imei" -f /path/to/firmware.hex command on the terminal. It prompts as ERROR flash <deviceId> failed!,
ERROR Error: No such...
Hi
I'm working with version v8.6.90 since the master version at this date have an Auth amplify issue.
The Fetch function on the map is buggy :
Here is the Chrome dev...
We are using nRF52 SDK 17.0.2 s132_nrf52_7.2.0_softdevice.hex in our application. When entering in DFU mode from application, we perform nrf_power_gpregret_set(BOOTLOADER_DFU_START...
I am willing to use nRF52832 chip in one of my project. But all the breakouts dont fit the size and I want to design my own PCB with i2C accelerometer. I only want to transmit...
Hi,
Corect me if I'm wrong, but the initiation of ble_gap_addr_t.addr_type in main.c in the HRS_C demo is not necessary, as the addr_type is calculated based on the address...
Hello Folks,
I am following below steps to add Zigbee FOTA to Zigbee: Light switch example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_zigbee_configuring_libraries...
Another problem is that when I turn on I2S to read data, the while loop does nothing, and the broadcast can't be transmitted, just like I2S has occupied all the CPU, and other...
