I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
after having a little break from ot and working on another project, I am back working on getting the NRF into systemOFF. to get back into it I just made a very small...
Hello there,
Prior to updating to the latest modem firmware i was able to successfully get responses from the DK.
Running the Asset tracker app as well as AT Client. ...
Hi
I am currently trying to connect the sht31 temperature / humidity sensor. First, I made an implementation based on the twi_sensor example. I did it all, the temperature...
Dear all,
I am quite new to embedded programming and I am looking for a tutorial/example code in order to communicate/configure an accelerometer sensor (LIS2DH12) with NRF52...
Hi,
I am running SDK 15.3, nRF52840 on a custom board, Softdevice 6.1.1 and SES.
When running the secure dfu example I find that the two segments uicr_mbr_params_page...
Hi,
NRF52932, s132.
I am currently migring from SDK 14.0.0 to SDK 15.3.0, I just finished to migrate from SDK 13.2.0 to SDK 14.0.0. The project with my app compile but...
Hi
I want to transfer a text filebetween nrf51 to nrf52 .Is this possible in nrf device. If it is How can i proceed ?. I am using NRF 15.0 SDK.
Please help me on this...
Hi
We are using today nRF52832 and communicate through Nordic UART service (NUS).
Sometimes we would like to transfer files from our device to the app. This is going very...
Hi All,
I have an application running on the nRF52832. From within the application I can store data to 0x2000 2010 - 0x2000 2028 and read the data back after a reboot/power...
Hi,
I need to generate a PWM signal with exact 2.048 MHz. I've just realized that
allows only decimal frequency. Even if I take 16 MHz and toggle it every 7,8,9 still...
Hi,
I have the NRF52 dev kit with NRF522832 chip. I am using SDK version 15.2 and the Segger IDE. I am trying to do OTA programming and have used this tutorial:
https...
I followed the nRF User Guide v2.2 for my nRF dongle and all was Ok up to "Install firmware with SEGGER J-Link point 6 e (loadfile Path\...\sniffer_pca10031.hex)". Got error...
Hi!
I am trying to get this example to work on my nRF9160 board: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi/
It compiles and...
Hi,
if got the following setup:
Nordic nRF52840 DK (peripheral), custom iOS App (central), nRF Connect Desktop Version + another nRf52840 DK as sniffer.
My Goal: Changing...
Hello,
I need to interface both, an SD card and a smaller (~4Mb) external flash to the nRF52840.
The SD card will be interfaced using SPI.
For the external flash...
