Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi, just posted this question on the Github project of the iOS app but I think this is the "official" place to ask...? :) anyways https://github.com/NordicSemiconductor/IOS...
I am trying to upgrade from nRF Connect v2.3 to v2.4 for Windows 10 (x64), but antivirus software(offline (Avira) and online versions) gives warning message "BDS/Androm.hrhsn...
Hi,
Downloaded the nrfconnect-setup-2.6.0.exe file.
Scanned it with www.virustotal.com, and it detected a W32/GenBl.55BA2A95!Olympus virus.
Can you please check it up...
I would like to use the nRF52840 as the subject device in a EE Capstone design course. Compiler tools (both Keil and Segger) work well and will be easy to teach but I am unable...
In the "sdk_config.h",there has two options, one is TIMER_ENABLED,the other is NRFX_TIMER_ENABLED, and in the sample ,there also have"nrf_drv_time" ,what's the difference...
I am trying to program an EBYTE 2G4M04S1B module. After connecting to the NRF-DK, in nRFgo Studio, I get the "No device detected, or readback protection may be set GUI", but...
Hi,
I try to implement the access to the SoftDevice functions in an application. I started with the TWI example and want to implement fstorage module from the SDK (SDK15...
The file components/libraries/serial/nrf_serial.c in nRF5 SDK is used for UART serial tx/rx and has support for timeouts. There appears to be a bug with use of timeouts. ...
hello,
I want to use the Nordic's smartCoap library(nRF5 Iot SDK v0.9.0) on my linux UDP,
I want to know if the Nordic's smartCoap library can really do this,
if can...
Hi,
nRF connect programmer can works with nRF52840,nRF52832 without problem.
I am trying programming nRF52810.
But, The read,erase all function always unavailable. ...
If I look in the schematic of the nRF52832 I see 3 VDD Legs (leg 13, leg 36, and leg 48), What is the leg number for the main power to the chip, that if I cut his power supply...
I am trying to rotate my oled screen 90 degree, but i couldn't.
I had surfing a lot for it, but still i have not perfect solution.
So please any one can suggest me or give...
Hey - I know there's no official support for C++ on this platform, but are there any other intrepid devs out there making this work?
I was able to build, flash and run my...
Hi All
I mount a NRF52810 minimum system for test BLE . It can works at no BLE mode , but don't work at BLE mode. The 32.768KHz clock works well . When I run a ble_app_blinky...
I use nrf52832 board, S132,SDK14.2 . I refer to some projects and nrf52 datasheet that indicate to use pin sensing mechanism( level trigger ) to wake up device from system...
