Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi Support,
I am using
I have my own customized board with nrf52840 . i am using SDK v15.0.0 with Softdevice verison v6.0.0
I am advertising with DFU and NUS services...
Hello,
I used the uart example to print text over serial communication from the SDK v11.
The problem is when I write lot of text consecutively, I don't receive all data...
i use the BLE uart example to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL and MAX_CONN_INTERVAL...
Hi,
Some time ago I ask a question about changing the publish address of a node in the mesh locally. I received the answer in the following threat and verified it:
https...
Hi All,
I used the app "ble_app_uart" and "ble_app_uart_c" on two custom boards mounting a n52840 QIAACO.
I know that in the app (nRF5_SDK_15.1.0_a8c0c4d\examples\ble_peripheral...
Dear Sir/Madam,
I want to measure the data speed between two BLE 4.2 based devices and two BLE 5.0 based devices.
Using nRF52 products for this purpose.
Kindly help...
I know that the nRF52832 is strictly a 3.3V device however, I was wondering whether any of the GPIO pins are 5V tolerant?
Is there any internal clamping diodes within the...
Hello,
I have noticed, that https://github.com/NordicSemiconductor/nrfx was updated with a nfct driver. I am trying to extended the nrfx port on micropython (see https:...
Hi,
I'm trying to setup the Peer Manager on a nRF51822 with installed the S130. I'm working with Eclipse where I installed the 12.3.0 SDK.
At compilation time I get the...
Hi, I have a two part question, I know the NRF51822 (and I believe all 4.0 BLE chipsets) are being sunset, when will this start taking place?
Since I'm currently using the...
HI,
i am using nrf51422 with sdk13.3.0 and soft device 130
i am receiving 69 byte of data through UART, i am compressing data in two packets. here after transmitting a...
I have an issue with BLE on Android when using low duty-cycle directed advertising and I'm asking here hoping some people have already seen that issue or something similar...
Hi,
I'm working on a custom bootloader based on the one included with SDK 15.
I have a blocking method (i.e. while loop) that runs at the end of the transmission of all...
Hi,
Some general Nordic BLE device questions:
How to add Characteristic?
How to send data to given c haracteristic?
We are using SoftDevice 132 with Segger IDE.
...
