Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi Sir, I am use Laird BL651 module, which use nRF52810. I am use nRF52 DK debug output (P19 and P20) connect to our board, but the nRFgo studio not able to detect device...
Hi Nordic,
A problem was found with the SDK15.2 write operation. If the write size is equal to 12000 bytes, the system will return an invalid operation length error.
But...
Hello. I am developing an Android app and Arduino BLE device that will need to work in a very population-dense environment. Think a very large music festival with thousands...
Hello All,
I am trying to interface an analog sensor with nrf52832, whose analog values have to be converted using SAADC and has to be sent over SPI to another chip. But...
I am working on a project where an nRF52 is a multi-role BLE device. It is an advertising Peripheral, to which smartphones can connect, and a Central which scans for and connects...
Help, I want to run NRF_LOG_ENABLED builds but occasionally I want the device to sleep for (many) minutes, so I wish to turn off the NRF_LOG_UART backend since it consumes...
I plan to test BLE and Zigbee communication range in multiprotocol examples.
And I haven't found how to configure Zigbee tx power.
Questions:
1. Is the tx power of BLE...
Hi all,
I am trying to interface HI-3585 with nrf52832 through SPI which works fine. Now i have merged the code with saadc program so as to transmit adc values through HI...
Hello.
I am building nRF Mesh SDK using cmake (gcc).
After successful building the code, I flashed hex file to nRF 52 DK.
I want to know free space in DK after flashing...
We want to use nRF52840 as advanced USB - UART converter to control end device (see structure below).
We already checked that our end device is working fine by external...
Dear Support
I’m having a problem erasing the network configuration data in the flash.
We are using nrf5_SDK_for_Mesh_v2.0.1 with the flash manager according to this post...
I am new and trying to install and run samples on Raspi 3B but cannot. Have anyone worked with Raspi 3B and nrf52840 dongle and please give me some instructions.
Hi I'm using Android Studio 3.2 and github.com/.../Android-nRF-UART My Samsung SM-G570Y (Android 7.0 API 24) works no problems but the Samsung SM-G955F (Android 8.0.0, API...
Hi. I am developing a gateway using SDK15 and nRF52840.
I'm advertising 4 devices every 20ms.
Theoretically, it should be scanned 50 times each, but in reality it is...
I tried to add an additional characteristic to NUS service as below.
However, any mobile apps could find only existing Nordic Rx and Nordic Tx characteristics, other than...
