I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
The sample program uses "nRF5_SDK_15.0.0_a53641a".
Hardware uses Taiyo Yuden's "EYSHSNZWZ"
In addition, we use a sample of [ble_app_uart] and [ble_app_multilink_central...
I have been running through the mesh network examples using nRF52840 chips, from light switch, dimming etc. I now want to know how i can send adverts between the nodes of...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Hi all,
I know there are some questions about this already but I could not find a solution.
I'm adapting this example for my internship. I'm currently testing throughput...
Hi,
So, we have got some requirements and would love to hear some suggestions or guidelines in choosing the a Nordic module and protocols that would get the stuff done....
The Bluetooth specification states:
If more than one Characteristic Presentation Format declarations exist, in a characteristic definition, then a Characteristic Aggregate...
Hello,
we want to add to our in-production solution the option do DFU OTA.
So we followed this step-by-step guide: https://devzone.nordicsemi.com/b/blog/posts/getting...
I'm curious about the CPU lockup reset. We have a long term test with 9 units running identical firmware on identical hardware; line powered, running continuously for 6 months...
Hello,
I have a problem with turning on notification on a characteristic so I can start receiving data.
I am using a nRf51 dongle as a client device, using softdevice...
Hi, I would like to establish services with following security permissions in a Bluetooth 5 peripheral: Currently I use the NRF52-DK and SDK 15.2 Service A: Security level...
I'm trying to adapt the secure_bootloader example for our custom board with a nRF52832 QFAB with 32kB RAM and 256kB Flash, following the information in this thread:
https...
I'm building a project on top of cli examples:
<SDK>\examples\peripheral\cli
<SDK>\examples\ble_central_and_peripheral\experimental\ble_app_interactive
My goal is...
Hello
I need to setup the the PWM peripheral@ 8MHz with one selectet Channel in DMA mode. For development, I am using the NRF52840 Preview Dev Kit PCA10056 (Q1AAAA). I did...
I have one question, if Nordic can give some confirmation, that Nordic chips can be used together
with Murata XRCGB32M000F1H00R0.
Customer just asks for that I don’t...
Hi,
In my project NRF51422 need to communicate with two peripherals which are supporting only UART communication.
please help me if there is any possibility.
Thanks...
