Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
This might be a simple one, but i cannot figure it out.. How do I place the rx/tx/rts/cts lines from UART0 on a GPIO1 pin?
In the piece of DTS below, 'tx-pin' is on...
nrf Toolchain: 2.7.0 nrf Connect SDK : 2.7.0 Gateway: nrF5340 Audio DK Headset: E arbud 'MOMENTUM TW 4' (Sennheiser) I try to run and test this following application Unicast...
Hi!
In my project i am using a motion sensor that uses a custom protocol. This has resulted in needing to implement bitbanging for it to work. The issue with this is that...
Hi,
I want to obtain the nrf52833‘s’ temperature with the SoftDevice enabled, and I have designed the code with reference to the example project. However, once the temperature...
Hi there,
I am trying to get nRFConnect working in VSCode, but when i click on things in the welcome screen it only shows "activating extensions..." in the bottom bar. I...
1) On p. 55 of nRF52805_PS_v1.4.pdf, section "5.3.8 Reset behavior" shows that a pin reset will reset GPIO, so will a pin reset active low also reset PSELRESET registers,...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hi,
I have built and run the MQTT sample for an nRF7002-DK and had it work as expected (connect, publish messages to test.mosquitto.org).
Now I'm trying to get that sample...
I created a new application using the "Create a new application" > "Copy a sample" > "zephyr/samples/basic/blinky" option in vscode. And I added a new build configuration...
Hi Nordic community,
I'm currently working on a project where I'm aiming to implement FOTA updates on the nRF52840 DK, with the application images stored on the MX25R64...
Both a colleague and I discovered that the default Device Provider, nrfutil, is not working in the current versions of VS Code and nRF Connect for VS Code extension. nrfjprog...
Toolchain v2.6.1 installed. Attempt to Manage SDKs fails.
[13:12:52] nRF Command Line Tools 10.24.2 are up to date Command failed: git ls-remote --tags --heads github.com...
First attempt to use the Power Profiler II on Windows 10 didn't work. I was getting [sdfu] No deviceInfo available for the device, code: Argument. Message: Operation device...
