Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Reporting this here as the project GitHub asked that bugs be reported via DevZone.
The latest Power Profiler v4.2.0 has introduced an annoying issue - when running the Power...
I have an application that gets a fix using A-GNSS. I couldnt understand from the documentation how to enable other satellite systems other then GPS to be enalbled in my application...
Hello,
I am trying to run this Android-nRF-Blinky sample from Git ( https://github.com/NordicSemiconductor/Android-nRF-Blinky ) and build failed.
Below is the error message...
I make a BLE/USB MIDI controller that has an NRF52840 receiving sensor data by SPI from an Atmega 32u4 at 2Mhz. The NRF52840 is the SPI master (SPIM3). When I'm using BLE...
Hi there, I am using nrf connect sdk v2.6.0. I have noticed that after DFU update, I am seeing ble bonding lost randomly on firmware side. I did uncheck Erase Application...
We are running some sample code on the nrf54l15 mcu, specifically: /modules/lib/memfault-firmware-sdk/examples/nrf-connect-sdk/nrf5/memfault_demo_app
We can connect and...
Hi nRF support team,
I am evaluating ST7735 LCD with the nRF82540 development kit. For your information, I am able to set-up the nRF Connect SDK environment on nRF82540...
Hi Sir, I am developing with the nRF52840.
I installed nRFConnect 5.2.1 and the programmer (version 4.6.2), Following the programmer’s prompts, I installed SEGGER J-Link...
SDK version: 3.2.4
I am using two nRF5340 Audio DK boards configured as gateway and left headset.
I added " CONFIG_STREAM_BIDIRECTIONAL =y" to prj.conf and I built everything...
Hello,
I am working with the nRF54L05 and testing SAADC inputs.
I observed the following behavior:
AIN4–AIN7 work correctly as ADC inputs
AIN0–AIN2 show unstable...
Hello,
I have some issues to do work a VL53L1X with NRF54L15 dev board.
Here are my codes
And here is the RTT console response :
Someone can help me please...
After updating from v2026.1.1327 to v2026.3.1484 on Linux, all previously installed SDKs disappeared from the Welcome view — the extension no longer recognizes them. Attempting...
Hi,
Recently I upgraded to nRF Connect SDK 2.6.1 and I was required to enable the GPIOTE in order to build properly. Doing this has significantly increased (nearly doubled...
Hello,
I currently have a DECT NR+ setup running on an nRF9151 based on the newer HELLO DECT sample, using v3.3.0 preview version of the modem. With these comes two files...
Hi,
1. Since I need to use PWM DMA to transfer 320 bytes of data to the PWM for sequential playback. 2. I wrote the following test example to test the nrfx pwm driver, but...
