Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello everybody. Using the nRF52840-DK board and the Nordic example ble_app_uart_pca10056_s140 I am sending 200 bytes, repeatedly, to the Nordic UART APP. Everything works...
Hi,
What is the best approach to use a block of flash in nrf52840 as EEPROM. Are there any pre-existing library support for the same?
Also which is the best flash operation...
Hi,
I have gone through the lfs file system from zephyr samples but I could not find any solid documentation for fs and spi flash drivers available.
I have written the...
Hello,
I want to use the PWM driver to change the output voltage with respect to analog input voltage. If I call the simple_playback_sequence from the SAADC event handler...
Good day. Some smartphones cannot connect to NRF52832 (SDK17): - iPhone XR - iPhone 11 Detection goes well, but smartphones cannot fully connect and freeze at the connection...
Hi Sir,
We tried to download the nwp_024 , and check the tape reel information of nRF5340.
But we could not find the nRF5340 lists in "table 2. Carrier tape dimensions...
Hey everyone,
I firstly want to preface this with my lack of credentials. I'm very new to embedded systems development and am figuring things out slowly so please bear with...
I want to initialize LFCLK on startup to reduce power consumption. I am doing it as given below. Is this the correct approach of initializing LFCLK to reduce power consumption...
Hi,
I am using nRF52840 as BLE peripheral, on a Zephyr application under NCS 1.4.2
I want to limit the connection interval to 7.5ms (min+max)
I can see that the only...
Hi Nordic DevTeam,
I am using nRF52840 (1MB Flash, 256kB RAM). I would like to store a log data to flash memory that I can extract them to my Android phone later on when...
Hi All,
I want to verfiy the current consumption of nRF52840. I'm using an nRF52840 DK and SDK 17.0.2 RTC example. below are the verfiy steps:
1. Cut SB40 on PCA10056...
Hi,
I we are developing project on BLE NRF52832 module and it warked correctly. during the debugging suddnely it stoped responging to programmer and couldn't be reprogrammed...
I have read about eddystone protocol. I have run
nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_eddystone\pca10040\s132\arm5_no_packs
i am able to build the code...
