Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
We currently have an older Sena SD1000 bluetooth module in an embedded system that functions as a UART wireline replacement. We just connect it to a UART on the embedded controller...
Hi, I have a simple application with logic is: - every 3 or 20 seconds send some data via modem (based on AT commands), - sending and receiving data via serial port to and...
Hello,
I am attempting to find gerber data for the development PC or a mechanical drawing of connector locations. I would like to make a PCB that plugs into this board...
Hi, guys! I noticed this answer from the devzone .
I have nRF52 DK and an nRF Thingy. I want to play a short speech using I2S with MAX98357A .
This speech is usually...
Hey,
simple question: What is the recommend approach on prolonging the advertising period?
Example:
User clicks a button -> advertising starts for 180 seconds.
User...
Hi Support,
I am testing current consumption of NRF_TIMER1, below is my code snippets, basically, I just start timer1 task and then stop it.
After the two code lines...
Hi there, I really much in trouble with USB CDC ACM. So that would be great if you can help me out with this: I upload the "USB CDC ACM" example (SDK verison 15.2) to my nRF52840...
This is a question of curiosity rather than a specific concern: In my sdk_config.h I have my prescaller set to 0: Based on this, the RTC1 used for AppTimer should rollover...
I am working on an older project that was developed using SDK 11.0.0, SD S132 2.0.1, and "Eclipse 2018-9." No MDK appears to be being used.
I understand that the MDKs are...
Hello,
BLE 5 applications on the nRF52810 which softdevice should we be using S112 / S132 what are the primary differences between these? I wanted to know a comparison...
Hi,
I'm collecting data from BLE and storing them into nRF52840 Dongle by using nrf_fstorage_write procedure. Everything works fine so I can write data into flash by nrf_fstorage_write...
When I run the TWI scanner example, an unknown address shows up in tandem with my TWI device address.
I am connecting a MAX30101 EV kit daughter board to the nRF52840...
In the secure DFU bootloader, I have some custom initialization that I need to happen after the BLE transport is initialized in nrf_dfu_init(), but before loop_forever() in...
Hello everyone,
I've got an issue with ESB. I'm using 3 nRFs 52840 with firmware based on SDK 15.2. One of them, the radio-receiver is RX, and two of them, PilotA and...
