I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Is there any documentation on the advertising state machine ? This post :
devzone.nordicsemi.com/.../
mentions the state machine and how it progresses from fast, to...
Hi all,
I want to update my connection parameter as follow:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) //400 /**< Minimum acceptable connection interval...
Hi,
I'm doing a project using the Evalution kit.
I don't know why, but I can't go under 350 uA current comsumption in system on.
I did clear all pins,i did NRF_SPI0-...
HI:
i use SPI is ok when i set frequency = NRF_DRV_SPI_FREQ_1M,but SPI will work abnormal when i set frequency = NRF_DRV_SPI_FREQ_500K/NRF_DRV_SPI_FREQ_250K/NRF_DRV_SPI_FREQ_125K...
I am evaluating chips for a new project.
I am looking for a chip that can connect with Sony PS3, PS4 controller and most modern/recent cellular phones.
I am confused...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I tried to modify the twi_master_using_app_twi to work with adafruit ADS1015 as a slave. I ran into this problem. It seems that the init_transfer doesn't finish so the app_twi_perform...
What development kit should I buy? Is this the right one?
www.mouser.hk/.../
What software IDE to use?
Does Keil offer free version for limited code size? What...
trying to build a simple example in sdk 11 just to run it on the nrf52-dk
of course it is missing pieces, else life would be no fun, apparently...
oh, i don't know,...
Sorry for asking as not familiar with BT terminology and un-sure which fold means what, grateful pointer to example (in SDK or similar) that can run on the dev kit. That is...
What is "1 Mbps Bluetooth low energy mode" for nRF52832?
How was the spec. changed from my old year 2013 understanding that BLE is low speed for sensor, sending tens of...
I can read temp value by pulling flag but I Want to do that by interrupt
I added this code to my Keil but interrupt on temp didn't work.
I use Adc interrupt like this definition...
Hi,
We are using NRF51 and STM32F0 on our custom board and one of our customer's requirement is the ability to program both of these MCUs in the factory. They would like...
I am using the mbed compiler.
When I produce code using the "App with Bootloader" option, I can do FOTA updates and my code runs fine, as long as I don't enable the ble uart...
Hello together,
we are running the DTM in different modes to check the module (nrf52832, sdk 5 version 11). The carrier test gives us a current consumption that meets the...
