Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Is there any way that can allow the user to advertise a sine wave for example over a specific channel or over the three Radio channels ?
I am using S130 and Nordic SDK 8...
Hello,
As a summary (described fully below) I have loaded the ble_app_hrs example onto my device and its not working right as LEDs that should light up don't and the program...
In some of the Nordic examples I found by viewing the raw advertisements that the company ID is set to Nordic's ID (0x0059). In order to communicate with Apple devices (e...
Hi Nordic Support community,
I asking regarding LNP, Location and Navigation Profile, if it's possible to on top of nordic products? If so like which ones ?
There's barely...
Reading the documentation Address config it is clear how to use RXADDRESSES, could you please explain how to use TXADDRESS ?
As of TXADDRESS there are 3 bits available...
I am having trouble with using shockburst (based on microesb from github) after disabling S132.
When I use microesb with no SD, i just do nrf_drv_clock_init(), start lfclk...
Hi,
I am new to Nordic development platform and am exploring ways to develop software applications to communicate over bluetooth. Presently, I am working with NRF51422...
Hi, I have a problem about gpiote interrrupt.I have set two ports to detect the external interrupt(low to high). If only one port get active ,it works fine. But if one port...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi I am beginner to nordic ble. I have four nrf528** development kit. I am just trying demo heart rate example with android toolbox app. Suddenly one of my nrf devlopment...
I am currently using MBR, and know the general interrupt latency due to MBR + SD from Table 26. But I cannot understand how you arrived at those numbers. IF this table was...
Hello All
Hi, I use nRF52832 with SDK11 Version. But SDK11 didn't provide any CSCS central example. Anybody wrote ble_cscs_c.c for BLE / Cycling Speed and Cadence Service...
Yo men,
I study this web
infocenter.nordicsemi.com/index.jsp
Experimental: Flash Storage
I have 100 bytes data need to read/write/store.
So I think even this is Experimental...
Hi guys,
I compile a provided example with my nRF51_DK and it works well. But when I re-run the program, it will be block in function "sd_rpc_open()". The only solution is...
