Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I found several posts on this forum closely related to my problem, but non of this answer my needs. I try to program nRF51822AA with blinky example via Keil uVision...
Hi, in evothing and mbed all the UUID are 128bits long
however, in EK, the code use 16bit UUID
ex. nus.c the uuid is 0x0001 0x0002 0x0003
any one knows how to provide...
Hi,
I have just received my smart beacon kit (nRF51822 based), I have wired up my JLink programmer according to devzone.nordicsemi.com/.../
However I am having trouble...
Hi!
I'm building a mesh using beacons. Everything works good untill now, except beacons sometime stop advertising on its own. Beacon still works because he still connects...
Hi. We are going to mass production now and the lab that will certify our product says we need to have a special mode in the firmware that would do : modulated middle channel...
I want to make a custom board using nRF51822. Currently I am using nRF go studio starter kit and pca10005 board. I am using segger jtag programmer for loading code to the...
Hello,
I have a custom program based on the uart example. I can write to the device, but sending to the master fails.
I call the SendString code, but p_nus->is_notification_enabled...
Problem
I got some problem in change device name.
I found that the function of ble.gap.setDeviceName(deviceName) is useless.
So I've searching for another function...
Hi,
Does anyone know if there are plans to support RTX in the nRF52 SDK? It is included in the nRF51 SDK under external/rtx , and there is an example in examples/peripheral...
Hi,
I have purchased the nRF8001 DK and it came with no documentations. I downloaded the nRF8001 DK User Guide V1.1.
In this documentation, under section 1.3 there is...
I have setup environment on QT creator and i am using JLink GDB server debugger.The nordic chip is nrf51822 QF AA H0 and SDK is nrf51822 s110 version 8.1.0 .I read some posts...
I donwloaded the iOS nrf toolbox. I found that the app converts the glucose measurement to KG/L and not to mmol/l? The reading on the glucometer is in mg/dl so when I multiplied...
Hi,
I am trying to get my mesh running on the nRF52 Preview DK but calling
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);
will break my program...
I am using nrf51422 and ble app uart as my example code and trying to connect to my ios app nrf toolbox by enabling a static key for the pairing process. i have read all the...
