I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to get started the pc-ble-driver-py tool. What I would like to do is perform a scan for available BLE devices, connect to one of them, then write to a characteristic...
Hi guys,
to process the NFC data sent from a smartphone to NRF, I use the " nfc writable ndef msg example" . However, the issue is that I cannot find a variable where the...
I'm using a timer to read the ADC repeatedly using PPI. On ADC read finish I call nrfx_saadc_buffer_convert ready for the next timer event. However, if I want to cancel conversion...
Environment:
SDK v15.2.0
Raspberry Pi 3 (as a border router - Jessie).
MQTT broker in Linux PC (Mosquitto)
nRF52840 as a MQTT Publisher.
Without TLS-PSK, MQTT...
Dear all,
I'd like to re-init sd-card when detect it plug/un-plug. But i face a issue when i re-mount sd-card it can not open file....My flow as below
what is the best...
I'm extending an existing central application to support extended advertisement and CODED phy support. However, I have trouble connecting to a device advertising with CODED...
I am using nrf52832 with sd 6.0 and sdk 15.0. My application is based on the buttonless DFU example, and I am using a bootloader with OTA DFU. To update the application I...
Hi,
We are planning to finalize NRF52840 part for IoT project and below are the features/criteria that we are looking, Kindly confirm whether below features will be supported...
Hi,
I've recently hit an issue where sd_ble_gatts_rw_authorize_reply in my code returns INVALID_PARAM when I try and write a long set of data to a characteristic using...
Hello,
I am using the PCA10040 DK, and I want to get a 8 MHz OR 4 MHz clock output from one of the GPIOs.
I've followed the instructions from here
and it works.. however...
Hi there,
I’m trying to find the path-of-least resistance to get the GPS working in the Asset Tracker demo on a PCA10090 (v0.8.5), and I noticed that one of you engineers...
Hi, I am wondering if there is a way to reject Bluetooth pairing with Nordic peripheral outside of my own mobile application. For example the Fitbit devices will reject connecting...
In documentation:
Libraries > Serial interface > Serial interface library > Serial commands > Serial command groups > Serial command details > Access Layer Model Pub Period...
In following this example: https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/scheduler-tutorial
once I added
APP_SCHED_INIT(SCHED_MAX_EVENT_DATA_SIZE...
Where do I get the output (from the main apps printf/printk etc) from the Thingy:91 once it's connected via 10-pin swd-cable to my nrf9160 DK?
I don't think there's anything...