I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
I am facing some issues on the Android part of the BLE.
Firstly it takes around 20 seconds for the android phone in scanning mode to find the nordic board. This...
I encountered the following error while adding device manager to ble_uart_app in SDK_11 s130 using the hardware nrf51-DK. I'm using Keil compiler.
._build\nrf51422_xxac_s130...
While using the device manager, I encountered this line;
#define SEC_PARAM_MITM 1 /**< Man In The Middle protection not required. */
Since security is important, is...
Hello!
I'm trying to test several types of ANT communication like broadcast, background scanning, etc.
And When I check ANT broadcast rx example, I realized that some...
Hi Support Team,
i want to know the voltage range of AVDD(internal DC/DC output) of NRF51822 when DC/DC enabled, please help to check.
i don't find this information in PS...
I use nrf51822xxac, sdk 9.0.0, sd130. When I connect to some beacon as a central I no longer receive BLE_GAP_EVT_ADV_REPORT and I am not able to receive advertising packets...
Hello,
We do not want our beacon on at all times. I suppose our need below has been asked before.
Is there a sample snippit of code, or a document on ble_app_beacon...
hi:
i want to create timer in my code, i create timer and start the timer ,but the timer do not work,i found timer number can not exceed four,detailed information in the...
I found a bug in the FreeRTOS port provided by Nordic for the nRF52832 in SDK v11.0.0. This bug only applies if configASSERT_DEFINED is equal to 1, as the affected code is...
Hi,
We are assessing the pros and cons to port our software to work on S130. We are currently using S110 (Peripheral) and S120 (Central) on nRF51822 rev.3.
Based on the...
I am running ble_app_uart sample code on nRF-dk using SoftDevice n130. It is working fine.
Currently, when nRF UART app connects to ble_app_uart, user does not need to...
I have hard time in start a twi in nrf52832 with SDK11.0, I can't initial twi ,whatever i do ,when i build is still an error ,here is my code:
static const nrf_drv_twi_t...
Hello. Nowadays I'm trying to upload the softdevice for the RTOS based on the freertos.
As you know, determinism is very important for the realtime.
I want to know the...
Hai guys,
I am using nrf51dk, S130, and Keil to develop a simple project. My aim is to send the sensor data from the nrf51422 to the mobile app.
when no mobile is available...
I read this thread: nRF51 beacon high frequency scanning and advertising and have similar problem here.
Some repost from my electronics.stackexchange.com question
...
