Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hello,
I am planning to use an atmega32u4 as a micro controller for a keyboard, and I'd like to use a NRF51822 as the bluetooth sender.
As i've read, NRF51822 is BLE...
I would like to learn a little more about the process of negotiating a connection interval between an iOS and Android central and a nRF51 peripheral.
So, here are my questions...
Hello,
I purchased a nRF52DK to migrate my older projects running on nRF51822.
Version of the board is V.1.1.0 / 2016.19
I followed the 'Getting started' guide from...
Hello,
This is a DFU custom project...the core problem is that I cannot erase the bootloader settings page from the chip.
While trying to use a slightly modified version...
Hi
In current Desktop 2 project, We know that software device stack takes 48-bit random device address from FICR registers (DEVICEADDR[1: 0]) for BTLE. Each nRF51 has unigue...
Hello, I am devleoping a pc station using pc-ble-driver.
I was successfully able to install it on one of my computers but am facing a problem installing it on my surface...
The micro-ecc works well when I load micro_ecc_lib_nrf52.lib in keil5. However, the author suggest copying the uECC files into the project, so I include uEcc.h but fail in...
For the nRF51822, the documentation for ECB mentions it being used to
Encrypt/decrypt 16-byte data using
current key.
But it doesn't offer any methods to decrypt...
Hi,
Am using SDK 11.00 and NRF52 platform.
Am following below steps for dfu support.
1.Flashed Softdevice 2.00
2.Flashed dual bank ble Bootloader
3.Using nRFTool box...
Yan,
You mentioned these UART examples: examples\ble_peripheral\ble_app_uart or examples\ble_central\ble_app_uart_c I was not able to find them on your web site....
I have intention to use 52810's PWM output to drive motor. The timing requirement are critical so
hardware PWM is essential, rather than CPU generated waveform output.
...
Hi,
I am trying to increase MTU size for transfers and it works up to a size of about 72. After that I get an error.
Thanks to Sigurd I now know that it is when calling...
Hi, I've an application developed with SDK v8.0.0 and S110 v8, that is using the bootloader to start the main firmware and to start the DFU OTA (in case the user request to...
I currently have a problem with the gpiote setup. I'm using it to detect an interrupt from mma8652 accelerometer.
here is an annotated version with the key portions of...
