Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am trying to use nordic nrf51822 and transreceive data through ble_app_UART
and (Android-nRF-Toolbox) github.com/.../Android-nRF-Toolbox.
But i am not able to compile...
Hello,
In the reference layout for NRF52840 package (QIAA), the shape defined in the SOLDER PASTE is a bit larger than the one defined on TOP LAYER (copper) for each terminal...
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. We are now in the stage of power optimization. Therefore we bought...
Hello,
I have used the NORDIC power calculator to calculate the current consumption for different advertising intervals.
Adverting interval (ms) Current (mA) calculated...
Hello is a starter developer
I used the nrf51822 chip on the pcb board and downloaded the example code but it did not work.
When I checked the 16mhz external crystal on...
Hi all,
I am a bit confused about the use of SOFTDEVICE_HANDLER_APPSH_INIT and similarly APP_TIMER_APPSH_INIT. I've not been able to find anything in the documentation...
nrf52840, S140.
So for the past 1 or 2 weeks I have been fighting with this problem :
Now it turned out that the connection handle may actually be INVALID, it's 0! ...
I am using nRF52840 DK as a SPI slave with an external MCU configured as SPI master. The SPI clock frequency is set to 1 MHz. I am using the following pins for SPI:
P0...
Hi All,
I have just got my nRF51 kit (S130) and started working on a beacon project which would transmit advertisements packets from peripherals over a RS485 to a server...
Hi,
im running my DK as a central of a BLE connection and i'd like to read the device_name of the peripheral board that im communication with. how do i do this? i cannot...
Testing on nrf52DK (QFAAB0), without softdevice, unfortunately still on SDK10 and
NRF52 sleeping on RTC. Programming pins disconnected.
Measured:
low frequency clock...
i am total beginner to the nrf51822. i am going through the nan-36_v1
app note is using s110 but i can't find that soft device in sdk ? is there any changes has to be done...
Hi,
I took the ble_hrs_c code and modified it such that it has the NUS service and can connect to 2 peripherals. The code works when I power cycle the central+2peripheral...
hi Engineers!
I am trying to use int. pullup of 160k but no effect. the voltage remains zero on pin.
config.resistor_p = NRF_SAADC_RESISTOR_PULLUP;
what problem?
...
Hi All,
sometimes i have a problems with bonding: the Nordic APP said "Couldn't pair with xxxxxx because of an incorrect PIN or passkey".
Why i have this errors? What...
