Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
HI, we want to develop DFU over NBIoT network (UDP), and we would like some advice on how to implement that. We are using nRF52832.
Looking at your SDK examples for BLE...
Hello Everyone,
I am trying to integrate LIS3DSH accelerometer with nRF52832 development board(I2C communication). I have Implemented Wake-up State Machine for LIS3DSH....
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi folks,
I've found no beeter way of reporting this (no public SDK repo which allows issues with code reference).
I tried to TX ESB DPL frames from an nRF52840 to different...
Hi all,
I want to sell a device that I have made that uses the nrf51822 and the app inside the chip is derived from the ble_app_uart. It uses two chips that communicate...
When I send my app to people, it uses a specific version of pc-ble-driver. I would like to make sure dongle used was programmed with the hex file package with this specific...
Hi,
I'm having issues with my nRF9160. I followed the steps under "Getting started with development", but I keep getting the following error when updating the mfw:
I...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
The state machine (figure 118 in PS V1.4) shows that the NFCT can be activated by either issuing the TASKS_SENSE...
Hi ,
I am using the secure bootloader example (SDK 15) as a template for my DFU solution.
I am experiencing issue with the update process as the device shuts down after...
Hello
In our project we are using NRF52840 SoC.
Up to this point NRF52840 chip is used as BLE module to be able to connect our device to cloud over gateway.
now we are...
I have added DFU service in my custom application and I am able to upload the zip file of my application over the air by connecting to the DFUTarg using nrfconnect in my mobile...
I'm developing the PCB schematic for a system using the nRF52 and have some questions on the SWD programming interface.
It seems that I only need 4 pins for the Segger...
Hello,
I am curious, does nRF52832 support USB Type-C in terms of data transfer and Power Delivery? Or will I need another MCU to handle data transfer and Power Delivery...
Hi,
We've developed a custom board with buttons(peripheral) which will talk to another custom board operating as a repeater (central on one side to talk to our custom board...
