Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
I am connecting nrf52832 to a windows computer, and it connects to it, but after a while (30 seconds), it disconnects automatically. When i try to debug it, i see a...
Hi,
the nRF5 SDK v13.0.0-1.alpha uses the BLE_GAP_PHY_CODED constant to indicate a coded PHY.
The BLE 5.0 standard specifies two options for coding: S=2 (500 kbit/s...
My app (SDK12.3.0 + S130 v2.0.1) is being prevented from advertising because flash_access_in_progress() is true (m_queue.count != 0) on ble_advertising_start (ble_advertising...
Hi! I'm trying to add the nRF drv_timer library to the ble_app_template example project (BLE Peripheral).
I have added the nrf_drv_timer.c file to the project, and the directory...
I need to switch between 3 central devices (device slots, rather) with a peer manager and SDK 12.3.0 (nrf51822-based keyboard, see sdk12_3 branch for a peer manager https...
Hi,
I have a problem, like this fellow engineer here , but the solution is not applying for me.
Our firmware support different modes of operations. Mode changes are...
Hi,
I was testing out the nrf52840, and i wanted to initialize the BNO_080 sensor with the nrf52840 DK. Now, i realized that if i want to read from registers to get the...
Hi, I'm using nRF52840-DK , SDK 15.0, buttonless DFU sample + secure bootloader I see that resuming DFU works only after disconnect, but no longer on sw reset or power down...
Hello
I have seen in the various examples that most of the time the output are digital (0 or 1) . i program a PWM signal to make any DC output on the pin 18
but unfortunately...
I am developing a windows deskop application for BLE devices.
which laungage is the prefered for this type of Desktop application having predefined libraries..
Nordic...
We have an application running on a custom board with the following configuration:
nrf52832
SDK v12.3
Softdevice S132 v3.1.0 and S332 v2.0.0 (different variants of PCB...
Hi, I am using nRF51822 now,SDK11.0, how to let the peripheral open the peer's notification, My original design uses DA14580, Android APP can receive messages when the peer...
hello .
i am trying to open driver in the advertising.py example pc-ble-driver-py-master
driver.open() and this line throw exception
if err_code != expected: raise NordicSemiException...
It seems nordic devices can not be programmed without certain segger software.
In order to set up my toolchain, I had to install SEGGER Embedded Studio IDE (although i dont...
I have seen nordic contains QDID 111537 for mesh profile subsystems. Is this profile subsystem includes the Mesh Model or nordic have a plan to get Mesh Model QDID seperately...
