Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I'm trying to implement the HID service on a custom nrf52832 board, unfortunately I'm running into problems.
Here's what happens: Advertising, connecting to the board,...
Hi,
I think I already know the answer but just to be sure, there is no difference on using printf (with added retarget library) and the app_uart_put() since printf will...
Hi, This is what constant carrier looks like at 2450MHz on my custom board using DCDC disabled
This is with DCDC enabled:
It can also look much worse with no real...
Hi there,
I'm looking at porting (i.e. re-implementing) an Arduino project to the nRF52832 to take advantage of the s212 or S332 softdevices. This chip is a few orders of...
I want to created a connectable iBeacon with nRF52810. I would like to connect my beacon through an app like nRF Beacon app and would like to configure....
* UUID
* Major...
Trying to run the SPI Master application on a custom nrf52382 based device (custom PCB) to communicate with an ADC chip that is taking analog values from a Multiplexer. Not...
I've designed a custom board for the NRF52832. Current consumption is not a major concern, and the pin location was convenient, so I wanted to use P0.00 and P0.01 for I2C...
Hi,
This is a problem report for the Programmer App v1.0.1 on nRF Connect v2.6.1 on MacOS 10.14.2. I have been attempting to use the programmer app with the nRF52 Dongle...
Hi all,
I have a trouble. I use 2 Dev Kit NRF52832. Flash light switch server proxy and light switch client proxy. Issue is when I erase and flash the first time, Client...
I'm developing an application for the nRF52832 using the nRF5 SDK version 15.0.0. We're using the s132 softdevice, the sample secure bootloader (modified to use our company...
Hi, I have been running into a problem where I am getting inconsistently failure to start advertising.
Calling:
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hello, I'm trying to write code to a custom PCB with a nRF52832 using the nRF52 DK and the following wiring:
However, everytime I try to connect the JLink is says...
I'm fairly new to working this close to hardware and am playing around with a few things. I'm trying to bit bang i2c over a couple of gpio lines and everything seems to be...
1.Does nRF52840 and nRF9160 have conformal shielding in manufacture procedure？
2.Do i need reserve shield cover for these two module when I develop product？
