I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I'm using vanilla version of the dfu_dual_bank_ble_s110 project on top of my application. The problem is that the firmware enters bootloader mode whenever a USB is connected...
Is there a way to figure out for which target a binary in _build/ is compiled with Keil?
(other than parse .map or .lnp file for a file unique to the target)
hi , I am trying to download the softdevice(v8) and cross compiled application(using makefile in nrf51822 sdk v6) from my Linux PC using JLinkExe.
following is the memory...
if i am a master i want know to know the sleep period of node,how do i know...?
how do i know whether it is sleeping or awake..?
if i have data to sent for node,but...
nrf51822_AA rev3, SDK8.0.0, S110 8.0.0
My application has the max number of bonds set to 24 with a size of 128bytes each. So that's 3 pages. Plus one page for saving user...
Hello,
I want to generate timer events as exact as possible, based on a time base that is defined by a runing timer. For example, I've setup timer0 to count up every 1µs...
Hello,
I want to use the Segger drag and drop programming feature on the PCA10028.
I have got a running application with the S120 softdevice.
To use the mass storage...
After 6 days hard work finally completed a C++ class to implement MultiCeiver and Enhanced ShockBurst….
But the “Product Specification PDF” contains some errors:
a) Page59...
What's the best way to ask the device manager how many bonds it has? Or even, whether it has any bonds at all?
I can see nothing in the API docs here:
developer.nordicsemi...
Hi all,
I asked this question before but I am not able up to now to find solution. How to use DFU example of SDK 7.1 for the S130 SoftDevice. I have tried some flash address...
I am currently developing a bootloader for N548 chip from Dynastream/Nordic.
I am following the project example for the S310 soft device and using IAR.
The project had been...
So I see ble_app_hrs and others have some nice examples of buttonless reboot into DFU bootloader. But for security reasons, I'd rather the user hold down the reset button...
hi, I am very new to ble and I am trying to download softdevice S110 to my Yunjia NRF51822 board. I am using J LINK connected to my linux PC to download the softdevice to...
Hi：
I used a design with nRF51822-QFAA+BAL-nrf01D3+Pi-network+SMD chip antenna,but it didn t work well.I tested the VDD_PA Pin ,it didn t have a 1.6V voltage(datasheet),that...
