SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi, We have custom nrf52840/33 peripherals, advertising every couple hours, and passing/receiving information from centrals running node.js version 12.22.5 with pc-ble-driver...
Hi, I work on custom board, which have NRF52833 and IS25LP016D SPI flash. I tried with SPI flash sample but SPI flash driver IS25LP016D was not found! err message show on...
Hello,
I want to use DTM FW for my design and have to update Tx & Rx pins to 21 and 20 respectively. Looking at the files in $\ncs\v1.8.0\nrf\samples\bluetooth\direct_test_mode...
Hi
I measured the CW output power of several DevBoards (nRF52832 and nRF52840) and the output power is much lower than expected.
Setup:
nRF52832 or nRF52840 DevBoard...
Hi Nordic,
when I run the samples/subsys/fs/fat_fs, the example of FAT file system usage with SDHC media, get error as below:
I have no idea how to fix it.
the SD...
Hello, sorry to disturb you I'm using Nrf52840 board and I would like to know how to flash correctly. I'm going to tell what i did with Visual Studio Code. I created a simple...
hello guys ,
In my project i am trying to reduce power consumption of nrf52810 with sensor. when a device is powered up it consumes 1.2mA without BLE advertisement and i...
We recently changed from nRF52832 to nRF52833 and for layout convenience used some of the P1.xx pins for our signals.
We are using SDK ver: nRF5_SDK_17.0.2_d674dde
For...
Just installed nrF Connect SDK v1.8.0 (using Toolchain Manager) - under Windows Windows 10 Entreprise
I have completed the setup and restarted my PC, however VSC is not...
Hi everyone,
I experiment with the saadc low power example . I have followed all the settings but I cannot achieve as low power as the example. As you can see from the PPK...
Hi,
1.How to test the ESD Human Body Model (HBM) performance of nRF5340?
2.How to test ESD Charged Device Model (CDM) performance of nRF5340?
Thank you for all your...
Hi everyone,
I have just purchased the PPK2. I've noticed that there two methods two measure the current
1. Source meter (the PPK2 provides power to the DUT)
2. Ampere...
Good day!
I have a question about length in MPID. In current implementation size measures in uint16 size and this brings lot's of troubles when you try to decode values...
Hi, I want to run UART on my custom PCB module that uses Wuerth Elektronik Thyone-I module that has nRF52840 chip. The project has just a RX, TX pins (and power supply, of...
