Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hello,
For our product, we wish to store a custom post-production name (essentially a serial number) in the UICR registers of the nRF52840. We understand that this can...
I am using a code similar to App_uart_C from SDK17.02 - central sending data over uart to another peripheral.
After 30-60 sec, the operation stops probably due to an error...
Dear Fellow developers
I am developing an application where I need several nrf51 USB dongles (S120) attached to a PC, and I need a way to distinguish one dongle from another...
I am integrating PWM into my project which uses SDK_15.2.0.
My config.sh contains:
and I have included nrfx_pwm.c.
Compiling the project I get this error:
Trying...
The project I'm working on is running off of a CR2032 battery. I want to measure the battery voltage while the radio is transmitting to determine when the battery dips down...
Hello,
I am using "pdm sensor" with "NRF 52832". we have PDM Drivers provided by the NRF . I just want to understand how we can connect the data and clock pin with nrf ...
Dear Members,
I create a loop inside main.c using code example ant_shared channel,
it's merged with ant_plus hrm_rx, but on forever loop, it stopped on 6 loops, it's...
Hello!
A frequent question in the forum is how to enable logging messages.
My question is exactly the opposite: I experience many NRF_LOG_INFO messages from Nordic library...
I'm having some issues with a design I'm developing using the ISP1807 bluetooth SOC (contains nRF52840). Every time I apply power to my device I have to manually reset the...
Dear Members,
How can I display multiple ANT channel ?
It looks like one channel is occupying all the resource (HRM)
How can I manage the time slice between channel...
Hi,
We are building our synthetic sensors using nRF52840 for smart buildings. In some areas we are using it with BLE only, other areas we use it with BLE mesh. When we want...
Hi,
Hope you are well.
I want to send the saadc data with ble to my pc. I used the below code. I am getting the data in the right format but i am loosing some data in...
I am experience some for me strange behavior with UART0 on a nrf52832. Let me explain:
First I initialize the UART using:
APP_UART_FIFO_INIT(...)
with parameters setup...
Hi,
I am using Ozone with nrf52840.
I used this example: wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52840
I am able to debug fine. However, I am unable to see...
