Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I tried to reduced my hex file's size while converting to zip but it doesn't get size under 256KB due to which I am getting an error: Data size exceeds the limit.
Below...
Hey,
I don't get my application run on the nrf52840-dk board. Only if I choose "Build and Debug" I can run my software. Shouldn't the application start after I connect to...
I would like to receive data on UART asynchronously and handle the RX event in the backend in an IRQ handler. The application is - a user will be shown a menu and asked to...
Hi Sir,
If we would like to supply the external device through VDD = 1.8V when VDDH = 2.5V.
What is power efficient in nRF52840 when VDD = 1.8V when VDDH = 2.5V?
...
Hi!
We have been experimenting with the nRF9160's GPS using both one of our own custom board and the Development Kit v 0.8.5 (with similar results).
We run the gps sample...
Hi,
I am receiving the same error this guy was: " https://devzone.nordicsemi.com/f/nordic-q-a/28724/sdk-for-mesh-v1-0-0-with-ses-invalid-ascii-encoded-byte-line-1 " and...
Is the Altium integrated libary used in the Altium files for the nRF9160 DK available anywhere? It is not included in the hardware file download on Nordic's website.
Looks...
The problem is shown in the picture below.
It is normal for 10 seconds after activating the timer.
As you can see in the picture, the value of the time stamp changes...
Our application uses and external nand flash to store the data samples. The collected data is then be transferred using USB. So we chose usbd_ble_uart example and wrote code...
Hey,
I am working on mesh with nrf52 DK. I want my device to work on battery for long time, I have enabled the MESH_FEATURE_LPN_ENABLED macro in nrf_mesh_config_core.h file...
I'm returning an error code on a rw_authorized characteristic using uint32_t sd_ble_gatts_rw_authorize_reply(uin16_t conn_handle, ble_gatts_rw_authorize_reply_params_t * auth_reply...
When using the PB-ADV bearer there is a ~10 second delay after the Link is closed and the mesh stack starts working again.
This is related to my previous report https:/...
I am trying to develop a SPI interface to a CANBUS controller for the nRF9160 for the zephyr platform.
The issue I am having at this point is is that I am unable to see...
