Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
I've installed Zephyr RTOS and built blinky example for NRF5340-DK board. Then, when I tried to flash output hex file into NRF5340, nrfjprog (using "west flash" command) gave...
I'm trying to debug firmware on our production device, but after programming the device a couple of times, I am unable to program.
Inside of Segger I see this log:
j...
Hi everyone,
In my company we are working with the last SDK release, and we build projects with make and gcc toolchain.
I have a quite wide request : since I'm using makefiles...
Hi all,
I have a custom nRF52840 board that transmits 32-byte packets to mobile device and I want to achieve maximum transfer speed.
The code is based on the ble_app_uart...
Dear all
The issue is:
heartRate and battery levels set by "bt_gatt_notify" in peripheral hr sample on nRFConnect v1.5.0 are not shown in iphone app of "nRF toolbox" ...
Hi All,
I am using the nRF52840, with SDK140 v15.0. I have configured the nRF52840 to be a SPI slave to a NXP processor. When I connect the logic analyzer I see signals...
Hello,
I am trying to build on the nrf5340_cpuappns sample, however this snippet seems to always warn unable to allocated UART send data buffer. Is there any reason k_malloc...
Hi Everyone!
nrf_serial.c and nrf_serial.h are gone in SDK 17.0.2. There are present in 16.0.0. I do not see any mention of this in the release notes.
Was this module...
i am using example code ble_uart for controlling gpio(led & buzzer) by editing bluetooth data handler. I am driving a buzzer using pwm.
led working fine i.e turned on/off...
In nRF Connect SDK I see drivers for BH1749 sensor from Thingy 91, but not for BH1745 from Thingy 52.
Is it possible that the BH1745 sensor will be supported soon? Looks...
I tryed to use the pynrfprog with a Segger-ARM-Flasher to update modem DFU.
I changed the python skript to follow - because there are 2 Segger-ARM-Flasher installed in...
Hi,
When I connect my device to an external power supply, it restarts randomly. It sometimes happens once every minute, sometimes once every 10 minutes. I couldn't find...
Hello,
I am transmitting 1 byte BLE data across a central and peripheral and the central does other things like control PWM, sample SAADC (scan mode), GPIO pins interrupts...
Hello,
When I am loading my project into SES I get the following warning message.
CMake Warning at C:/Zypher/v1.5.0-rc1/zephyr/CMakeLists.txt:1354 (message):
WARNING...
