Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hey All -
My team is new to Bluetooth development and so this may be a naïve question. Pardon us for this, if so.
We are trying to create an Android App that would scan...
Hi,
There is a difference of one digit in BT address and DEVICEADDR. Could anybody explain this? I know in the last byte we have to add C0, but what about the frst byte?...
I added CCCD descriptor to Battery Level characteristic in the proximity_setup.xml.
The nRFSTudio throws an error 0x01 while generating services.h.
Kindly help me generate...
8.0, multilink example, peripheral, s110 softdevice.
I modified the button_event_handler() function in main.c into this:
static void button_event_handler(bsp_event_t...
Hi....
I have a problem when i use dfu_dual_bank_ble_s130_pca10028 in sdk v11 on my board. cpu is nrf51822QFAA.it seems reset all the time. using keil debug, it's wrong on...
The CoAP block example has a "put" function, which works just as the instructions describe. It would be helpful if you could also show an example of the "get" function. These...
hello!
Is IoT softDevice for nRF51 DK has all the features of BLE 4.2??
I know IPSP is the feature of BLE 4.2, but i wondered whether privacy and data packet extension...
app : nrf tools on git hub
s130: sdk v11
s110: sdk v8.1.0
example : nrf_ble_uart.
after modify, it happen, is there some definition shoud modify in app?
by the war,the...
Hi All,
I'm using Nordic UART App to write 'A' to TX characterstic and then i expect some action after that as per my code on BLE nordic device, which is happening.
But...
I'm using the attached proximity_setup.xml ( proximity_setup.xml ).
I'm trying to use the Battery Service to send Battery Level notification.
I added the following code...
Hi,
I have just received a nRF52832 Preview DK and I am trying to set it up according to the description in the nRF52 Series - Get Started section.
I have connected the...
Hi All,
I am using nRF51422DK with SDK 10 and trying to communicate with an external peripheral over UART at every timer interrupt.
I have modified the ble_app_hrs example...
Hi All -
Is there anyone successfully able to autoconnect with nrf51822 with a phone/pc/tablet? I have been trying it for the past week and couldn't get my nRF51822 autoconnect...
I successfully turned off bluetooth radio using NRF_RADIO->TASKS_DISABLE = 1 when i do advertise_start(); after certain delay i coudnt connect back for data transfer
Based on nRF51822\Board\pca10001\ble\ble_app_hrs example,
How nRF51822 detect ADC input? Which ADC pin?
Configuration code:
NRF_ADC->CONFIG = (ADC_CONFIG_RES_8bit <<...
