I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
I am using the nRF52832 in several projects for several different clients. I have created a "project" under Visual Studio using VisualGDB for each one, using the automated...
Hi,
I would like to know how to raplace a MPU-9250 chip with ICM-20948 in a Thingy:52 circuit.
Let me first state that my electronics engineering knowledge is at hobby...
So I've had a LOT of problems getting power management to work with UARTE on the 52840. We're using both UART_0 and UART_1 and have finally gotten UART_0 to work as it should...
When attempting a DFU update (containing APP + SD + BL) with the android version of nRF Connect, it appears that connect will update the device's application even when bootloader...
Is it possible to pass a memory location to PWM (preferably via DMA) via PPI. This is a sound project and my intent is to update two 8 bit PWM outputs at 44.1kHz. I typically...
Hi,
I am working on a project and I want to program the nrf52832 with the arduino IDE with this package ( https://github.com/sandeepmistry/arduino-nRF5 ). I want to use...
Are there any restrictions (eg, timing) or issues for using different references for different channels in Scan mode?
eg
AIN0 uses VDD/4 as reference;
AIN1 uses VDD...
Hi All.
Do someone know what is the oversize I get when I use the FS_storge example to store data on the interanl FLASH.
FOr every bulk I open (id+key). How much bytes...
I'm using nrf51822 and SDK 10, S110 Softdevice. Implemented whitelist using device manager and bonded with single device , after bonded my device with phone (using nrfconnect...
I'm using nRF51822 and SDK 10 , Softdevice S110 . I enabled whitelist option in my application its working as expected, but when after device is resetting peer device data...
Hello,
I am working on an application on a nrf52840 using soft-device 140 and SDK 15.3. I have written 90% of the application using the ble_app_uart_c as a template for...
Some context: I am using an nRF51 with SoftDevice S130, which acts takes both central and peripheral roles, and uses UART to communicate to a peer MCU. I am currently facing...
Hello,
I am using Seeger for Flashing code and Debugging. I ported code from “flash_fstorage” example code to “ble_app_blinky”. I have few queries on write data into Flash...
Hello,
I am trying to configure Pin P0.09 as SCL pin for TWI. But I am not getting any results with this pin while I get data when any other GPIO pins are configured as...
SDK: 15.2.0
SoftDevice: s140 6.1.0
Hello,
I seem to keep finding conflicting information on how the NRF52 manages power to its peripheral devices and whether the application...
