Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I'm using the nRF52 as a master and an external RF chip as a slave. After configuring my spi bus using nrf_drv_spi_init(&spi, NULL, NULL), in my main loop, how do I...
I have used nRF toolbox to update bootloader and firmware to my nordic device. I was previously using iOS9 (I believe 9.3.5 - whatever the latest version was before iOS10...
Firstly,I used ios9.3.5 to DFU successfully,
But when 9.14(ios10 was pushed),then my iphone6s was updated to ios10,
finally DFU failed.
The device can enter in the DFU...
Given this answer , do the BLE_GAP_CONN_SEC_MODE_SET family of macros only relate to the Write permissions of the device name?
Maybe a better way to ask this is: Is it...
Hi,
I am referring nRF5 SDK for Eddystone ( github.com/.../nrf5-sdk-for-eddystone) .
Here GCC Makefile based projects are scheduled for a future release.
I am trying...
Hello,
sorry for the dumb question but do you know which software does Nordic use for creating/editing sequence charts like the one in the documentation?
infocenter...
Hello,
I am currently working with NRF openmesh but when I try to set a new handle i get an error. This is what I tried.
uint8_t ledje = 0x01;
rbc_mesh_value_handle_t...
Hello,
I am doing bluetooth transceiving test. About in 10 times of transceiving wtih App, I got 9 times success, but one time failure. From my observation, App and bluetooth...
I evaluating nrf52_dk board, to build an application with custom BT Service on the nrf52_dk using the mbed platform. I see the new platform nrf52_dk platform is available...
Hi!,
I'm working in a Android app to communicate with a nRF52/nRF51 boards.
I've been using Bluetooth Smart nRF51822 Beacon Kit.
But I think what I need is not possible...
How do I change the properties of the Generic Access service's "Device Name" characteristic to be Read Only, not Read and Write? I see this
BLE_GAP_CONN_SEC_MODE_SET_OPEN...
Hi,
We are sending data every connection interval which is a stream using the API sd_ble_gattc_write. Whenever there is a dropped packet from what we understand, the Softdevice...
I used SDK11, SD332, and no change anything.
the application reset as picture.
can you test this issue and give suggest ,why app reset?
D:\work\nordic\BLE\SDK\nRF5_SDK_11...
I need a code example (e.g. Health Thermometer) that runs on the Beacon Kit. I have tried several combinations of soft devices and code examples, but I can't get it running...
Hello,
I started implementing a project with the device manager. I am using the S120 as central.
I am able to connect to 3 peripherals at the same time (also nordic nrf51822...
