Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
Programmer 4.8.0 uses inputCoreInfo.codePageSize as the UICR size. On both an nRF54L15 DK and an nRF54LM20B DK, nrfutil reports codePageSize = 16 and infoPageSize = 4096....
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
My desired work flow is the following.
Input: Two electret microphones -> Audio ADC -> I2S Stereo -> nrf5340
Processing: Buffers (10-50 bytes) channel 2 to create delay...
We are implementing key handling for the nRF5340 and have come across an inconsistency between the CC312 and Oberon key management drivers. I wanted to verify if this inconsistency...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
