This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Hi,
Users of our product have reported issues with multiple versions of Hubitat hubs when pairing Zigbee. I'm investigating this issue and have reached a point where I could...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
As title.
In nRF54L15 DK, I set "SB_CONFIG_BOOTLOADER_MCUBOOT=y" in file "sysbuild.conf".
It makes main function GPIO toggle stop.
Do have any solution to prevent...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
Hello all !
Summary
While in power save the nRF7002 RPU powers down its receiver without sending a PM=1 (Null) frame first, so from the AP point of view the station...
Dear Nordic team,
we are evaluating the nRF9151 for a data acquisition application/device. Our first goal was to get the official HTTPS client sample to run on the nRF9151DK...
Hello,
I work on a zephyr project with updatable MCUBoot and two updatable images. This configuration ends up with an unbootable image. The reason is that the CONFIG_MCUBOOT_MCUBOOT_IMAGE_NUMBER...
This is a continuation of this ticket. nrf54l15 zigbee end-device is bound with its On/Off client cluster to a On/Off server cluster of another ZigBee smart lamp.
I can...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
We are currently experiencing an issue with the nRF7002 that appears to be present when coexistence is enabled: The nRF7002 becomes unresponsive, seemingly at random, multiple...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
We want to measure latency and PER between two OpenThread Nodes exposed to WiFi interference. Multiple Raspberry PIs, which are configured as AP and/or client, simulate flooded...
Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
