Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
I have verified The maximum channel table size NRF_GZLL_CONST_MAX_CHANNEL_TABLE_SIZE is 32.
but result_value = nrf_gzll_set_channel_table(my_channel_table, 32) return false...
Hi, I am trying to reach the highest possible throughput when sending data over usb to nRF52840 from a host computer, but I am reaching 4Mbps max. Is this reasonable or is...
Hello!
I am using a nRF52840 board for some really simple development. First I just tried to run the blinky example and connected with another BT device. It worked well...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello,
I am working on creating a custom board based off the nrf5340dk_nrf5340 board
I am following the tutorial here
https://academy.nordicsemi.com/courses/nrf-connect...
Hello,
I would like to know if there is official C# source code to perform DFU OTA for a NRF52840 from Windows without Nordic hardware (DK, dongles etc..), using only the...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hi
I am getting an error while building source code. The same code used to build while using NRF connect SDK version 2.5.1. Currently I am using nRF Connect SDK version...
Hi,
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
Hi, We are using `fota_download` library on our nRF9161 design running mfw-nrf91x1_2.0.1 to download a firmware upgrade image from our Amazon AWS server location. When trying...
Hello, I am currently using (\nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio\receiver)routine to develop.I want to check if the first N bytes of the received packet are...
Hi! I am using nrf32840 with free rtos,
and I have a loop that do the following
for(;;){
vTaskDelay(pdMS_TO_TICKS(intervalTime)); // go to sleep due to portSUPPRESS_TICKS_AND_SLEEP...