But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
hi..........
i am using nrf42840 ...segger 15.2 version
i am facing the problem in sleep mode
i used the command to sleep
static void power_manage( void ) { ret_code_t...
Hi guys,
I am currently using nrf51822 with SDK 11. I use Peer Manage to deal with paring and bonding encryption in BLE connection.
Please correct me if I am wrong but...
Hi,
When I'm trying the throughput on nRF52840 with SDK v14.2, I set up a 52840PDK as a 'repeater'; in which case the 'repeater' will receive the output (20kBytes in total...
which app should I use when I want to do LL BQB test with harmony on nRF52840?
it can not connected with harmony when I use DTM project. It seems the interface of nRF52840...
Dear nordic,
I am currently working with nRf52840. For designing antenna is there any role for dielectric layer thickness and conductive copper layer thickness
Hi all, I'm testing quick connections and communications using multilink(nus). I am using multilink central example in nrf52832(Central : softdevice v2.0.0 & SDK v11, Peripheral...
I am trying to measure the power consumption when transmitting data from an external device to nRF 52832 to a smartphone.
I am trying to measure the power consumption of...
Dear, I'm designing a PCB with nRF52832 and I will intend to use DCDC converter therefore I putted the two inductors (10uH and 15nH) between DCC and DEC4 pins. The same hardware...
Hi,
I am developing a project in IAR Embedded Workbench for nRF52840-Preview-DK. I have integrated different modules (ble, ADC, SPI, I2C) in this project. I don't have...
I like to integrate the nRF54XXX with a LNA/PA combo (skyworks RFX2401C or 66110). Could you please tell me which pin should be used to control the RFX2401C TX/RX? Which has...
Hello all,
I am currently working on a project to control a door lock and use ble_app_multirole_lesc as reference.
As measurement the current consumption is around 6.5mA...
Hi, I’m working on low power wireless sensor network. I have a big dilemma in choose of wireless mesh solution. Maybe firstly, what i need: 1. Support for low power devices...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
