But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
About this example
https://github.com/NordicPlayground/nrf51-ble-tutorial-advertising
It´s advertising the data
uint8_t data_response[] = "Many_bytes_of_data" with the...
Hi,
I was working with MCUBOOT and was curious too know from where the MCUBOOT release version number is been generated or fetched-
When building MCUBOOT using cmake...
Hello mates,
I am modifying the Light Switch Client and Server example, to send messages uint8_t from the client to the server instead of use bool on_ff with no luck yet...
I am currently using a 51dk board. I am trying to study low power system_on_wakeup_on_gpio in github. I built this code and measured the amount of current. I would like to...
Parameter setting code is shown below. I've verified that the settings are being reported back in events, so they seem to be taking place. However, I'm keeping track of the...
I am trying to get the application to enter DFU via the buttonless DFU service using SDK 15.2. It appears to be stuck because of an SVC call not returning. Both application...
Hi :)
I would like to test the nRF52840-Dongle in a Raspberry Pi 3B+ OS = Rasbian (the bluetooth 5 features: 2Mbps and Long range). but unfortunately I didn't find a nRF...
I'm looking for a gateway (or BLE 5.0 device that can connect to a gateway, e.g. USB dongle) that uses the nRF52 series solutions with an amplifier that brings the transmission...
Sir
We have a client that is using two NINA B3 (uses a NRF52840), one central and other peripheral. The peripheral is sending advertising packages, but the central is only...
Hi I'm very interested in studying this protocol, and I'm testing with nrf52832 kit development, loading the example "bike power meter tx" and app on android "ant + plugins...
Hi,
I'm using NRF52832 and a core adaptation for Arduino IDE. In my project I'm using both TWI and SPI interfaces. If for TWI I manage to reduce the current during sleep...
Hi everyone,
I am using a chip nRF52832 reading data from LIS2DH12 via TWI (all in a custome boad), then data will be send to Master nRF52832 DK ia BLE_NUS. However, when...
I have a new nRF52840 Dongle which seems to have either had a hardware failure while updating its bootloader or the updating was unsuccessful and now the device does not flash...
To do some test, I need micros(). This is the reason why I couldn't use RTC or app_timer.
When I tried timer example(nRF5_SDK_12.2.0_f012efa\examples\peripheral\), I could...
Hello, I need to use PWM to control GPIO and integrate it to work on simple COAP server app using nrf52840 DK.
I used "pwm_simple" example from SDK (not Thread/Zigbie SDK...
