We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello,
I am having issues integrating mesh functionality into a preexisting BLE project.
My project is based around an nRF53832, with SoftDevice S132 and uses nRF5_SDK_17...
Hi,
i want to connect my nrf5340pdk board with the MPU6050 sensor. They should be communication using I2C.
I read different information about the connection of the sensor...
Hi,
I have two questions about the nRF52DK power consumption when powered via USB .. one is for interest, but the other one appears to be an issue.
I have run some comparative...
Hi, I found an unexpected bug which leads to stuck at this point 856419>, app_error_weak.c, 105, Mesh assert at 0x0003AA3A (:0) it's happened after a fast setting the level...
Hello,
I am trying to spot a bug in which some memory corruption is happening. I don't know in advance at which address the corruption will happen, as it happens in some...
I want to trigger SAADC samples manually, when a certain BLE message arrives. I'd ideally like to have a trigger scan 4 individual channels.
I see two function calls, though...
I want to use the SoftDevice APIs to read and write flash on the nRF51822. Are there any examples of how to do this. I see all kinds of mixes between pstorage, NVIC (not sure...
Hello,
I am new to Nordic and quite new to ZigBee. Just had a short evaluation with Silabs so far.
My goal is developing a custom lamp for serial production that needs...
Hello,
I am trying to perform a FOTA update from nrfCloud to a Thiny:91 device, but I notice that a mansage appears forcing me to update to FOTA_V2. The problem is that...
Hi,
Are the functions implemented in drv_uart and uart_app even related to each other? I noticed that uart_app implements only some simple functions. Can someone please...
Good morning Now, using nRF52832, I want to implement multiple central devices (smartphones) with one peripheral device (nRF52832 Device) to simultaneously perform BLE Multi...
I'm trying to send ADC data through BLE using nRF52840.
According to the example codes named ble_peripheral/ble_app_uart , peripheral/saadc , I wrote a code and it is...
With SEGGER Embedded Studio 5.10d and nRF52840, the register view show TIMER0-2 with 6 CC registers but they only have 4.
It's quite confusing particularly when using the...
Hi everyone,
I have created a BLE connection utilizing E73-2G4M04S1B module from EBYTE with nRF52832 as its core.
My problem is its low range which is limited to 15meters...
I'm trying to figure out why my Xbee3 module can't connect to my nRF52480 app. I built the app using SDK 7.2.0 and Segger and it runs great. I can connect to it from nRF tools...
