Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Dear friends,
I want to realize dfu in 52840 DK by PyACI , i know there should be a bootloader firstly,
a) I have flash the seiral example(nrf5_SDK_for_Mesh_v5.0.0_src...
Hi,
i am working on dfu with nrf52dk. i am facing a problem when genrating private key.
in cmd i got error with following command
"C:\Users\admin\Desktop\a>nrfutil.exe...
Hi,
I'm using nrf52840 and connect it to a PC via NFC pad (which triggers advertising).
When I'm turning my device on, connection fails to be established. Only after...
When using the nRF52 I was able to program the device with a special test build which allowed me, via a simple CLI, to control the radio and set a channel, vary power, set...
Hi Team
im trying to change device name during running time..
i can able to change the device name working fine for connectable mode...but if i go for running time non...
the power consumption is about 6.12mW in BT connected, and consumption is about 7.75mW in advertising mode.
is it normal or has possibility to reduce it to extend the battery...
Hi, you must be sick of me!
Now that (somehow) I've got the BLE Secure DFU Bootloader to work on my nRF52840 DK board. I'd now like to load it on a nRF52840 dongle pca10059...
Hello !!
I am using ble_app_becon example code to send some data with device name. On central I'm scanning and searching with device name to identify at central side and...
Heija Guys,
I have a question regarding the usage of the Zephyr BLE and the PWM. I would like to use the Zephyr BLE Stack and the PWM Driver together. The Problem now is...
Hi,
i am working on dfu with NRF52DK. I am facing a problem with compiling a example dfu code "pca10040_s132_ble_debug" .
error message is "cannot find ../../../../.....
Hi,
We bought 2 pcs of nRF52840 Dongles and want to use them to test if a nearby BT device has the correct MAC address.
I've programmed them with "sniffer_nrf52840dongle_nrf52840_7cc811f...
Hello,
I'm using the "usbd ble uart " with twi scanner example to send a sensor value through an arduino 33 ble sense using nrf52832 and it works very well . but when...
Hi,
I'm using the light switch example in the nRF5 SDK as base for Ble-Mesh. I'm using a nrf mesh app for provisioning. I have both client and server model in my application...
When building a project that works with the SDK 1.5.0, I get the following...
r@mint:~/ncs.1.6.0-rc2/nrf/nordic_assist/nordic$ west build -b nrf9160dk_nrf9160ns
[0/12...
