Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
I am working on project, in which we using nordic nRF52840 chip. We need to flash the app+SD+BL image file in external QSPI memory.
After prevalidation, the DFU controller...
I'm having a problem using SPI within Zephyr. My custom nRF52840 board has 74HC959 shift registers to drive LEDs. I'm using the SPI bus to transfer LED on/off states and can...
After clicking on ACTIVATE SIM and having correctly filled in the SIM IICD and PUNK I am receiving the following message: Request failed with status code 503 What does this...
Hello,
Using scan sample I am trying to read drone Remote-ID. When broadcasting Remote ID via Wi-fi Beacon no problems occur, but once selecting only Wi-Fi NAN as delivery...
Hey! I'm working on a LE Audio project utilizing the nRF5340, where I need to stream audio both from and to the nRF and I have encountered the error "sw_codec_lc3: LC3 enc_bitrate...
Hello,
I can see there are some ADC examples on Github https://github.com/NordicPlayground/nRF52-ADC-examples But those examples are nRF SDK5. Are there any ADC examples...
Hello everyone,
I have a problem using pstorage_update. Normally it does as it should, but once i call ble_stack_init(); on my code, pstorage_update doesn't work anymore...
Hey,
I am trying to use the example for Sync_Advertising_conn to get a connection between 2 nrf5340 devices. but I get this message
the problem is in the config
CONFIG_BT_PER_ADV_SYNC_RSP...
Hello,
I am using the nRF52811 on a keyfob that transmits short packets when a button is pressed. The button directly connects power to the MCU, and the firmware immediately...
Hi,
I've just received my new nRF9161 Development Kit, but when going through the Quick Start, it fails to program.
Log:
2024-06-19T20:51:59.582Z INFO Initialising...
I am trying to interface nrf52833 devkit with BG95 devkit using PPP connection. For this I am using gsm_modem sample code. But when I am getting error while build configuration...
Hi,
We are wondering the current consumption in our custom board. The board has the following components (my FW view :)
nRF9160 - powered directly from batteries (either...
Hi
I use nRF7002-DK and sdk version as v2.5.2,download lesson8 exercise 3 solution and build was error as below log, which parts am I miss?
build config as below
...
Hello,
I a working on a project that uses the nRF5340 CCM peripheral (Network core) in an asynchronous mode. That is, I encrypt PDUs prior to scheduling them for transmission...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
