Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hello,
I am using the nRF9151 DK with the Serial LTE Modem (SLM) application.
I put the device into sleep mode using:
AT#XSLEEP=2
This successfully disables the UART...
Device: nRF52832
SDK: nRF5 SDK 15.0.0
SoftDevice 6.0.0
Hello. I'm using using the ble_app_multirole_lesc example with nRF5 SDK 15.0.0. I'm trying to debug using my sniffer...
Hello all !
Summary
While in power save the nRF7002 RPU powers down its receiver without sending a PM=1 (Null) frame first, so from the AP point of view the station...
Subject: Possible hardware issue with nRF52840-DK (PCA10056) power source switch or onboard debugger
Hello Nordic Support,
I recently received a new nRF52840-DK and am...
Hello,
I've been working on a feature lately that involves writing the OTP registers in UICR on nrf54L15; after writing the registers I also wrote the protected value (0x50FA50FA...
Dear all, I was excited with the announcement at WWDC last week that Apple was now supporting Bluetooth Channel Sounding on iOS 27 (currently Beta) They even had a session...
Hi,
I'm working on a project where I need to sample an ADC with an accurate sample rate. It essentially works except that I do not get the correct rate from the timer...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Dear Nordic Technical Support Team,
I would like to inquire about the following regarding the nRF54L series development:
Can I develop for the nRF54L series using...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi,
I have a couple of questions on migrating from Partition Manager to Devicetree since a particular example was not provided. Following the procedure in the SDK v3.3.0...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
Hello.
I have nRF52840 USB Dongle connected to PC with nRFConect desktop application 4.0.4
I'm trying to connect to our custom BLE peripheral device, which advertises...
I'm trying to add memfault to an existing project but I'm getting this error
I added this to my prj.conf
CONFIG_MEMFAULT = y
CONFIG_MEMFAULT_NCS_PROJECT_KEY = "**...
I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
